MC908GR16ACFAE Freescale Semiconductor, MC908GR16ACFAE Datasheet - Page 206

• Manufacturer Part Number: MC908GR16ACFAE
• Description: IC MCU 16K FLASH 8MHZ 48-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908GR16ACFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LIN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 37
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Controller Family/series: HC08
• No. Of I/o's: 37
• Ram Memory Size: 1KB
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: SCI, SPI
• Rohs Compliant: Yes
• Processor Series: HC08GR
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: ESCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, DEMO908GZ60E, M68CBL05CE, M68EML08GPGTE
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Serial Peripheral Interface (SPI) Module
When enabled, the SPI controls data direction of the SPSCK pin regardless of the state of the data
direction register of the shared I/O port.
16.11.4 SS (Slave Select)
The SS pin has various functions depending on the current state of the SPI. For an SPI configured as a
slave, SS is used to select a slave. For CPHA = 0, SS is used to define the start of a transmission. (See
16.4 Transmission
high and low between each byte transmitted for the CPHA = 0 format. However, it can remain low
between transmissions for the CPHA = 1 format. See
When an SPI is configured as a slave, the SS pin is always configured as an input. It cannot be used as
a general-purpose I/O regardless of the state of the MODFEN control bit. However, the MODFEN bit can
still prevent the state of SS from creating a MODF error. See
When an SPI is configured as a master, the SS input can be used in conjunction with the MODF flag to
prevent multiple masters from driving MOSI and SPSCK. (See
the SS pin to set the MODF flag, the MODFEN bit in the SPSCK register must be set. If MODFEN is 0 for
an SPI master, the SS pin can be used as a general-purpose I/O under the control of the data direction
register of the shared I/O port. When MODFEN is 1, SS is an input-only pin to the SPI regardless of the
state of the data direction register of the shared I/O port.
The CPU can always read the state of the SS pin by configuring the appropriate pin as an input and
reading the port data register. See
206
A high on the SS pin of a slave SPI puts the MISO pin in a high-impedance
state. The slave SPI ignores all incoming SPSCK clocks, even if it was
already in the middle of a transmission.
MASTER SS
SPE
1. X = Don’t care
MISO/MOSI
SLAVE SS
SLAVE SS
0
1
1
1
CPHA = 0
CPHA = 1
Formats.) Since it is used to indicate the start of a transmission, SS must be toggled
SPMSTR
X
(1))
0
1
1
MODFEN
MC68HC908GR16A Data Sheet, Rev. 1.0
Table
Figure 16-13. CPHA/SS Timing
BYTE 1
Table 16-2. SPI Configuration
X
X
0
1
16-2.
Master without MODF
SPI Configuration
Master with MODF
NOTE
Not enabled
Slave
Figure
BYTE 2
16-13.
16.12.2 SPI Status and Control Register.
16.6.2 Mode Fault Error.)
General-purpose I/O;
General-purpose I/O;
Function of SS Pin
SS ignored by SPI
SS ignored by SPI
Input-only to SPI
Input-only to SPI
BYTE 3
Freescale Semiconductor
For the state of