MC9S08EL16CTJ Freescale Semiconductor, MC9S08EL16CTJ Datasheet - Page 238

• Manufacturer Part Number: MC9S08EL16CTJ
• Description: MCU 16KB FLASH SLIC 20TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08EL16CTJ

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-TSSOP
• Processor Series: S08EL
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SCI, SPI, I2C, SLIC
• Maximum Clock Frequency: 200 KHz
• Number Of Programmable I/os: 16
• Number Of Timers: 2
• Operating Supply Voltage: 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08EL32AUTO, DEMO9S08EL32
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• For Use With: DEMO9S08EL32 - BOARD DEMO FOR 9S08 EL MCUDEMO9S08EL32AUTO - DEMO BOARD EL32 AUTO
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Serial Peripheral Interface (S08SPIV3)
Ensure that the SPI should not be disabled (SPE=0) at the same time as a bit change to the CPHA bit. These
changes should be performed as separate operations or unexpected behavior may occur.
13.4.2
This read/write register is used to control optional features of the SPI system. Bits 7, 6, 5, and 2 are not
implemented and always read 0.
240
Reset
LSBFE
MSTR
CPHA
SSOE
CPOL
Field
4
3
2
1
0
W
R
SPI Control Register 2 (SPIC2)
Master/Slave Mode Select
0 SPI module configured as a slave SPI device
1 SPI module configured as a master SPI device
Clock Polarity — This bit effectively places an inverter in series with the clock signal from a master SPI or to a
slave SPI device. Refer to
0 Active-high SPI clock (idles low)
1 Active-low SPI clock (idles high)
Clock Phase — This bit selects one of two clock formats for different kinds of synchronous serial peripheral
devices. Refer to
0 First edge on SPSCK occurs at the middle of the first cycle of an 8-cycle data transfer
1 First edge on SPSCK occurs at the start of the first cycle of an 8-cycle data transfer
Slave Select Output Enable — This bit is used in combination with the mode fault enable (MODFEN) bit in
SPCR2 and the master/slave (MSTR) control bit to determine the function of the SS pin as shown in
LSB First (Shifter Direction)
0 SPI serial data transfers start with most significant bit
1 SPI serial data transfers start with least significant bit
MODFEN
0
0
7
0
0
1
1
= Unimplemented or Reserved
MC9S08EL32 Series and MC9S08SL16 Series Data Sheet, Rev. 3
0
0
6
Section 13.5.1, “SPI Clock
SSOE
Table 13-1. SPIC1 Field Descriptions (continued)
0
1
0
1
Figure 13-6. SPI Control Register 2 (SPIC2)
Section 13.5.1, “SPI Clock
General-purpose I/O (not SPI)
General-purpose I/O (not SPI)
SS input for mode fault
Automatic SS output
0
0
5
Table 13-2. SS Pin Function
MODFEN
Master Mode
NOTE
Formats”
0
4
Description
Formats”
for more details.
BIDIROE
3
0
for more details.
Slave select input
Slave select input
Slave select input
Slave select input
0
0
2
Slave Mode
SPISWAI
Freescale Semiconductor
0
1
Table
SPC0
0
0
13-2.