MCHC908GR8AVFAE Freescale Semiconductor, MCHC908GR8AVFAE Datasheet - Page 76

• Manufacturer Part Number: MCHC908GR8AVFAE
• Description: IC MCU 8K FLASH 8MHZ 32-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MCHC908GR8AVFAE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 21
• Program Memory Size: 7.5KB (7.5K x 8)
• Program Memory Type: FLASH
• Ram Size: 384 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 32-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Configuration Register (CONFIG)
OSCSTOPENB — Oscillator Stop Mode Enable Bar Bit
SCIBDSRC — SCI Baud Rate Clock Source Bit
COPRS — COP Rate Select Bit
LVISTOP — LVI Enable in Stop Mode Bit
LVIRSTD — LVI Reset Disable Bit
LVIPWRD — LVI Power Disable Bit
76
OSCSTOPENB, when set, will enable the oscillator to continue to generate clocks in stop mode. See
Chapter 4 Clock Generator Module
the rest of the MCU stops. See
cease to generate clocks while in stop mode. The default state for this option is clear, disabling the
oscillator in stop mode.
SCIBDSRC controls the clock source used for the serial communications interface (SCI). The setting
of this bit affects the frequency at which the SCI operates.See
Interface (SCI)
COPRS selects the COP timeout period. Reset clears COPRS. See
Properly (COP) Module
When the LVIPWRD bit is clear, setting the LVISTOP bit enables the LVI to operate during stop mode.
Reset clears LVISTOP.
LVIRSTD disables the reset signal from the LVI module. See
LVIPWRD disables the LVI module. See
1 = Oscillator enabled to operate during stop mode
0 = Oscillator disabled during stop mode (default)
1 = Internal bus clock used as clock source for SCI
0 = External oscillator used as clock source for SCI
1 = COP timeout period = 8176 CGMXCLK cycles
0 = COP timeout period = 262,128 CGMXCLK cycles
1 = LVI enabled during stop mode
0 = LVI disabled during stop mode
1 = LVI module resets disabled
0 = LVI module resets enabled
1 = LVI module power disabled
0 = LVI module power enabled
Note: LVI5OR3 bit is only reset via POR (power-on reset).
Address:
Reset:
Read:
Write:
Module.
COPRS
$001F
Bit 7
0
Figure 5-2. Configuration Register 1 (CONFIG1)
MC68HC908GR8A • MC68HC908GR4A Data Sheet, Rev. 5
LVISTOP
6
0
Chapter 16 Timebase Module
LVIRSTD
(CGM). This function is used to keep the timebase running while
5
0
Chapter 11 Low-Voltage Inhibit
LVIPWRD
4
0
LVI5OR3
See note
3
Chapter 11 Low-Voltage Inhibit
(TBM). When clear, the oscillator will
Chapter 13 Serial Communications
SSREC
2
0
Chapter 6 Computer Operating
(LVI).
STOP
1
0
Freescale Semiconductor
COPD
Bit 0
0
(LVI).