CY8C3446LTI-073 Cypress Semiconductor Corp, CY8C3446LTI-073 Datasheet - Page 50

• Manufacturer Part Number: CY8C3446LTI-073
• Description: IC MCU 8BIT 64KB FLASH 48QFN
• Manufacturer: Cypress Semiconductor Corp
• Series: PSOC™ 3 CY8C34xxr

Specifications of CY8C3446LTI-073

• Package / Case: *
• Voltage - Supply (vcc/vdd): 1.71 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Speed: 50MHz
• Number Of I /o: 25
• Eeprom Size: 2K x 8
• Core Processor: 8051
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Program Memory Size: 64KB (64K x 8)
• Data Converters: A/D 2x12b, D/A 2x8b
• Oscillator Type: Internal
• Peripherals: CapSense, DMA, POR, PWM, WDT
• Connectivity: EBI/EMI, I²C, LIN, SPI, UART/USART, USB
• Core Size: 8-Bit
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Technology: CMOS
• Processing Unit: Microcontroller
• Operating Supply Voltage (min): 1.8V
• Operating Supply Voltage (typ): 2.5/3.3/5V
• Operating Supply Voltage (max): 5.5V
• Package Type: QFN EP
• Screening Level: Industrial
• Pin Count: 48
• Mounting: Surface Mount
• Rad Hardened: No
• Processor Series: CY8C34
• Core: 8051
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, SPI, UART, USB
• Maximum Clock Frequency: 50 MHz
• Number Of Programmable I/os: 28 to 72
• Number Of Timers: 4
• Operating Supply Voltage: 1.71 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Controller Family/series: (8051) PSOC 3
• No. Of I/o's: 25
• Eeprom Memory Size: 2KB
• Ram Memory Size: 8KB
• Cpu Speed: 50MHz
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant

I
8. Analog Subsystem
The analog programmable system creates application specific
combinations of both standard and advanced analog signal
processing blocks. These blocks are then interconnected to
each other and also to any pin on the device, providing a high
level of design flexibility and IP security. The features of the
analog subsystem are outlined here to provide an overview of
capabilities and architecture.
Document Number: 001-53304 Rev. *K
2
SDA
SCL
C features include:
Slave and Master, Transmitter, and Receiver operation
Byte processing for low CPU overhead
Interrupt or polling CPU interface
Support for bus speeds up to 1 Mbps (3.4 Mbps in UDBs)
7 or 10-bit addressing (10-bit addressing requires firmware
support)
Flexible, configurable analog routing architecture provided by
analog globals, analog mux bus, and analog local buses.
High resolution Delta-Sigma ADC.
Two 8-bit DACs that provide either voltage or current output.
Condition
START
ADDRESS
1 - 7
R/W
8
Figure 7-22. I
ACK
9
2
1 - 7
C Complete Transfer Timing
DATA
Data transfers follow the format shown in
START condition (S), a slave address is sent. This address is 7
bits long followed by an eighth bit which is a data direction bit
(R/W) - a 'zero' indicates a transmission (WRITE), a 'one'
indicates a request for data (READ). A data transfer is always
terminated by a STOP condition (P) generated by the master.
However, if a master still wishes to communicate on the bus, it
can generate a repeated START condition (Sr) and address
another slave without first generating a STOP condition. Various
combinations of read/write formats are then possible within such
a transfer.
8
SMBus operation (through firmware support – SMBus
supported in hardware in UDBs)
7-bit hardware address compare
Wake from low-power modes on address match
Four comparators with optional connection to configurable LUT
outputs.
Two configurable switched capacitor/continuous time (SC/CT)
blocks for functions that include opamp, unity gain buffer,
programmable gain amplifier, transimpedance amplifier, and
mixer.
Two opamps for internal use and connection to GPIO that can
be used as high current output buffers.
CapSense subsystem to enable capacitive touch sensing.
Precision reference for generating an accurate analog voltage
for internal analog blocks.
ACK
9
PSoC
1 - 7
DATA
®
3: CY8C34 Family
8
Figure
ACK
9
Data Sheet
Page 50 of 126
7-22. After the
Condition
STOP
[+] Feedback