CH80566EE025DW S LGPN Intel, CH80566EE025DW S LGPN Datasheet - Page 38

• Manufacturer Part Number: CH80566EE025DW S LGPN
• Description: MPU, ATOM PROCESSOR, Z530P, U-FCBGA8
• Manufacturer: Intel
• Series: ATOM - Z5xxr

Specifications of CH80566EE025DW S LGPN

• Core Size: 32bit
• Program Memory Size: 512KB
• Cpu Speed: 533MHz
• Digital Ic Case Style: FCBGA
• No. Of Pins: 437
• Supply Voltage Range: 0.8V To 1.1V
• Operating Temperature Range: 0°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

FSB
Frequency
V
V
V
V
V
V
V
V
V
I
I
I
I
I
38
CCDES
CC
AH
SGNT
DPRSLP
CC
CC
CC
CCBOOT
CCP
CCPC6
CCA
CCDPPWDN
CCPRSLP
Symbol
,
BFM
HFM
LFM
Table 9. Voltage and Current Specifications for the Intel® Atom™ Processor Z515
BCLK Frequency
V @ Burst Frequency Mode (BFM)
V @ Highest Frequency Mode (HFM)
V @ Lowest Frequency Mode (LFM)
Default V
AGTL+ Termination Voltage
AGTL+ Termination Voltage
PLL Supply Voltage
V @ Deep Power Down Technology (C6)
V @ Deeper Sleep (C4)
I for Processors Recommended Design Target
(Estimated)
Processor
Number
Z515
BFM: 1.2 GHz @ AVID Volts
HFM: 0.8 GHz @ AVID Volts
LFM: 0.6 GHz @ AVID Volts
I
CC
Deeper Sleep (C4)
6.
7.
8.
9.
10. The V
11. Unless otherwise noted, all specifications in this table are based on estimates and
12. V
13. The V
14. V
CC
V
Based on simulations and averaged over the duration of any change in current.
Specified by design/characterization at nominal V
This is a power-up peak current specification, which is applicable when V
V
This is a steady-state I
V
(burn in voltage is higher).
simulations or empirical data. These specifications will be updated with characterized
data from silicon measurements at a later date.
1.05 V ±5% on all power states.
1.05 V while exiting C6 (Deep Power Down Technology State) at least 5 µs before
V
during V
Voltage for Initial Power Up
CC,BOOT
CC_CORE
CC_CORE
CCP
CCP
CC_CORE
Core Frequency/Voltage
BFM: 1.2 GHz
HFM: 0.8 GHz
LFM: 0.6 GHz
may be turned off during C6 power state—V
(voltage rail which is turned off in C6, with SPLIT VTT Enabled) should ramp to
CC
CC
Parameter
tolerance is shown in Figure 6 and Figure 7.
maximum supported by the process is 1.1 V but the parameter can change
power supply needs to be set to 0.3 — 0.4 V during C6 power state.
CCP
is low.
are high.
ramps to LFM VID. In addition, V
ramp coming out of C6.
CC
current specification, which is applicable when both V
1.425
AVID
AVID
Min.
0.75
1.00
1.00
0.30
0.75
CCPC6
—
—
—
—
—
—
—
rail should remain at 1.05 (-5/+10%)
CCPC6
V
CC
100.0
CC
Typ.
1.05
1.05
0.35
. Not 100% tested.
1.5
—
—
—
—
—
—
—
—
—
LFM
must always be powered on to
Electrical Specifications
1.575
AVID
Max.
1.15
1.15
0.40
0.85
0.11
1.1
1.1
2.0
2.5
0.8
0.6
0.9
0.7
0.5
—
—
—
Unit
MHz
—
CCP
V
V
V
V
V
V
V
V
V
A
A
A
A
is high and
Datasheet
CCP
Notes
1, 2, 10
1, 2, 10
3, 4, 15
@ 50°C
12, 14
12, 14
1, 2
2, 6
1, 2
3, 4
3, 4
13
and
—
11