QB-MINI2-EE NEC, QB-MINI2-EE Datasheet - Page 120
QB-MINI2-EE
Manufacturer Part Number
QB-MINI2-EE
Description
EMULATOR, PROGRAMMER, MINICUBE2
Manufacturer
NEC
Type
Debug Emulatorr
Datasheet
1.QB-MINI2-EE.pdf
(169 pages)
Specifications of QB-MINI2-EE
Svhc
No SVHC (18-Jun-2010)
Mcu Supported Families
MINICUBE2
Silicon Family Name
V850, 78K0R, 78K0S
Ic Product Type
On-Chip Debug Emulator
Kit Contents
MINICUBE2, USB Cable, Target Cable, 78K0-OCD Board
Features
On-Chip Debugging, Flash Memory Programming,
- Current page: 120 of 169
- Download datasheet (6Mb)
5.2.6 Debugging of alternate-functions of X1 and X2 pins
120
program) and when programming is performed with the QB-Programmer.
device, so the X1 and X2 pins and their alternate functions can be debugged by using the following procedures.
To implement debugging of the X1 and X2 pins, the circuit must be designed appropriately.
5.1.5
(1) Disconnect the external parts connected to the X1 and X2 pins in the target device. (If the circuit is designed
(2) Turn on power to the target system and MINICUBE2 in accordance with 5.2.3 System startup procedure.
(3) Start the debugger.
(4) Terminate the debugger.
(5) Turn off power to the target system and MINICUBE2 in accordance with 5.2.4
(6) Connect the external parts to the X1 and X2 pins in the target device. (If the circuit is designed as shown in
(7) Turn on power to the target system and MINICUBE2 in accordance with 5.2.3 System startup procedure.
(8) Start the debugger.
Remark
Note If a project has already been created in the project manager (PM+), the load module will automatically be
The X1 and X2 pins are used when the debugger is started for the first time (when downloading the monitor
It is not necessary to use the X1 and X2 pins if the monitor program has already been downloaded to the target
as shown in Figure 5-11, short jumper pins 1 and 2.)
downloaded automatically immediately after startup.)
procedure.
Figure 5-11, short jumper pins 2 and 3.)
Connection of X1 and X2 pins.
downloaded. In this case, terminate PM+ and then start the debugger.
The next time the debugger is started, perform the procedure from step (7). However, if the program is
written via the QB-Programmer and the monitor program is erased, the procedure must be performed
from step (1) again.
CHAPTER 5
At this time, do not download the load module
HOW TO USE MINICUBE2 WITH 78K0S MICROCONTROLLER
User’s Manual U18371EJ1V0UM
Note
. (The monitor program will be
System shutdown
For details, refer to
Related parts for QB-MINI2-EE
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
16/8 bit single-chip microcomputer
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual audio power amp circuit
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual comparator
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
MOS type composite field effect transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
50 V/100 mA FET array incorporating 2 N-ch MOSFETs
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Twin transistors equipped with different model chips(6P small MM)
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Bipolar analog integrated circuit
Manufacturer:
NEC
Datasheet: