QB-MINI2-EE NEC, QB-MINI2-EE Datasheet - Page 30
QB-MINI2-EE
Manufacturer Part Number
QB-MINI2-EE
Description
EMULATOR, PROGRAMMER, MINICUBE2
Manufacturer
NEC
Type
Debug Emulatorr
Datasheet
1.QB-MINI2-EE.pdf
(169 pages)
Specifications of QB-MINI2-EE
Svhc
No SVHC (18-Jun-2010)
Mcu Supported Families
MINICUBE2
Silicon Family Name
V850, 78K0R, 78K0S
Ic Product Type
On-Chip Debug Emulator
Kit Contents
MINICUBE2, USB Cable, Target Cable, 78K0-OCD Board
Features
On-Chip Debugging, Flash Memory Programming,
- Current page: 30 of 169
- Download datasheet (6Mb)
30
(4) Connecting the USB cable
(5) Applying power to target system
(6) Debugger startup
Connect MINICUBE2 to the host machine as shown in Figure 3-11, before the power to the target system is
turned on.
When the power select switch is set to ″T″, the mode LED flashes white after connection.
When the power select switch is set to ″3″ or ″5″, the mode LED glows white after connection.
Turn on power to the target system. This step is not necessary if the power select switch is set to ″3″ or ″5″.
The mode LED glows white after power application.
Start the debugger. The mode LED glows blue after debugger startup.
For the operation after this step, refer to the user's manual for the debugger.
If the debugger does not start normally or the operation is unstable, the possible causes may be the following.
• Communication error between MINICUBE2 and target system
• The user resource has not been secured or the security ID has not been set
• Unsupported software (debugger, device file, or firmware) is used
• Defect of MINICUBE2
Whether communication is performed normally can be checked using the OCD Checker. For details, refer
to the user's manual for the OCD Checker.
To perform debugging with MINICUBE2, the debug monitor area and communication serial interface for
communication must be secured and the security ID must be set. For details, refer to 3.2.5 Securing of
user resources and setting of security ID.
The software used may not support debugging of the target device. Refer to the document ″QB-MINI2
Operating Precautions″ and check the supported version.
Electronics partner, refer to the documents prepared by the partner company.
MINICUBE2 may have a defect. Refer to CHAPTER 7 SELF-TESTING.
MINICUBE2
MINICUBE2
CHAPTER 3
Figure 3-11. Connecting MINICUBE2 to Host Machine
HOW TO USE MINICUBE2 WITH V850 MICROCONTROLLER
User’s Manual U18371EJ1V0UM
USB cable
USB cable
When using software provided by an NEC
Host machine
Host machine
Related parts for QB-MINI2-EE
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
16/8 bit single-chip microcomputer
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual audio power amp circuit
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual comparator
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
MOS type composite field effect transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
50 V/100 mA FET array incorporating 2 N-ch MOSFETs
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Twin transistors equipped with different model chips(6P small MM)
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Bipolar analog integrated circuit
Manufacturer:
NEC
Datasheet: