QB-MINI2-EE NEC, QB-MINI2-EE Datasheet - Page 152
QB-MINI2-EE
Manufacturer Part Number
QB-MINI2-EE
Description
EMULATOR, PROGRAMMER, MINICUBE2
Manufacturer
NEC
Type
Debug Emulatorr
Datasheet
1.QB-MINI2-EE.pdf
(169 pages)
Specifications of QB-MINI2-EE
Svhc
No SVHC (18-Jun-2010)
Mcu Supported Families
MINICUBE2
Silicon Family Name
V850, 78K0R, 78K0S
Ic Product Type
On-Chip Debug Emulator
Kit Contents
MINICUBE2, USB Cable, Target Cable, 78K0-OCD Board
Features
On-Chip Debugging, Flash Memory Programming,
- Current page: 152 of 169
- Download datasheet (6Mb)
6.2.6 Cautions on debugging
152
(1) Handling of device that was used for debugging
(2) Flash self programming
(3) Operation after reset
(4) Debugging with real machine running without using MINICUBE2
(5) Step execution
(6) Operation when debugger starts
(7) Debugging after program is written by flash programming
(8) LVI default start function setting (address C1H)
This section describes cautions on performing on-chip debugging for a 78K0R microcontroller.
Be sure to read the following to use MINICUBE2 properly.
Do not mount a device that was used for debugging on a mass-produced product, because the flash memory
was rewritten during debugging and the number of rewrites of the flash memory cannot be guaranteed.
Moreover, do not embed the debug monitor program into mass-produced products.
If a space where the debug monitor program is allocated is rewritten by flash self programming, the debugger
can no longer operate normally. This caution also applies to boot swapping for such an area.
After an external pin reset or internal reset, the monitor program performs debug initialization processing.
Consequently, the time from reset occurrence until user program execution differs from that in the actual
device operation. If Not Permit is selected in the Flash Programming area in the Configuration dialog box of
the debugger, the time until the user program is executed compared with the time when Permit is selected is
delayed several 100 ms.
If debugging is performed with a real machine running, without using MINICUBE2, write the user program
using the QB-Programmer. Programs downloaded by the debugger include the monitor program, and such a
program malfunctions if it includes processing to make the TOOL0 pin low level.
If step execution is performed for the following instructions, an extra instruction is executed.
a. RETI/RETB instruction
b. Conditional skip instruction (condition is not satisfied)
When the debugger is started, if the Target Device Connection setting in the Configuration dialog box of the
debugger is different from the setting for the previous debugging, the internal flash memory is erased.
If a program is written to the internal flash memory using the QB-Programmer or PG-FP4, on-chip debugging
is disabled even if it is enabled in the on-chip debugging option byte setting. To perform debugging of the
target device after that, erase the internal flash memory using the QB-Programmer or PG-FP4 and then
download the program using the debugger.
The LVI setting at address C1H in the internal flash memory during debugging is set as follows.
- When MINICUBE2 is connected: The LVI default start function is available.
- When MINICUBE2 is not connected: The LVI default start function is unavailable.
Immediately after returning from the interrupt servicing, an instruction is executed and then the execution
breaks.
The instruction following the conditional skip instruction is executed and then the execution breaks.
CHAPTER 6
HOW TO USE MINICUBE2 WITH 78K0R MICROCONTROLLER
User’s Manual U18371EJ1V0UM
Related parts for QB-MINI2-EE
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
16/8 bit single-chip microcomputer
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual audio power amp circuit
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual comparator
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
MOS type composite field effect transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
50 V/100 mA FET array incorporating 2 N-ch MOSFETs
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Twin transistors equipped with different model chips(6P small MM)
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Bipolar analog integrated circuit
Manufacturer:
NEC
Datasheet: