QB-MINI2-EE NEC, QB-MINI2-EE Datasheet - Page 57
QB-MINI2-EE
Manufacturer Part Number
QB-MINI2-EE
Description
EMULATOR, PROGRAMMER, MINICUBE2
Manufacturer
NEC
Type
Debug Emulatorr
Datasheet
1.QB-MINI2-EE.pdf
(169 pages)
Specifications of QB-MINI2-EE
Svhc
No SVHC (18-Jun-2010)
Mcu Supported Families
MINICUBE2
Silicon Family Name
V850, 78K0R, 78K0S
Ic Product Type
On-Chip Debug Emulator
Kit Contents
MINICUBE2, USB Cable, Target Cable, 78K0-OCD Board
Features
On-Chip Debugging, Flash Memory Programming,
- Current page: 57 of 169
- Download datasheet (6Mb)
Notes 1. Connect TxD (transmit side) of the target device to RxD (receive side) of the target connector, and TxD
Target connector
Target connector
RESET_IN
RESET_IN
RESET_OUT
RESET_OUT
2. During debugging, the clock mounted on the 78K0-OCD board can be supplied. If no clock is mounted, a
3. For debugging, short the jumper and mount no clock circuit.
4. This connection is designed assuming that the RESET signal is output from the N-ch open-drain buffer
5. The circuit enclosed by a dashed line is designed for flash self programming, which controls the FLMD0 pin
RxD
RxD
CLK
CLK
TxD
TxD
FLMD1
FLMD1
FLMD0
FLMD0
(transmit side) of the target connector to RxD (receive side) of the target device.
clock of 4, 8, or 16 MHz can be supplied. During flash programming, use the clock mounted on the target
system.
For flash programming and the target device operation (without MINICUBE2 connected), leave the jumper
open and mount a clock circuit.
(output resistance: 100 Ω or less). For details, refer to 4.1.3 Connection of reset pin.
via ports. Use the port for inputting or outputting the high level. When flash self programming is not
performed, a pull-down resistance for the FLMD0 pin can be within 1 to 10kΩ.
DATA
DATA
R.F.U.
R.F.U.
R.F.U.
R.F.U.
R.F.U.
R.F.U.
R.F.U.
R.F.U.
R.F.U.
R.F.U.
R.F.U.
R.F.U.
GND
GND
Note 1
Note 1
Note 1
Note 1
Note 2
Note 2
Note 4
Note 4
V
V
DD
DD
(with X1/X2 Communication, X1 Oscillator Is Used) (FLMD1 Pin Is Provided)
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
CHAPTER 4
Figure 4-5. When Both Debugging and Programming Are Performed
V
V
DD
DD
10 kΩ
10 kΩ
HOW TO USE MINICUBE2 WITH 78K0 MICROCONTROLLER
1 kΩ
1 kΩ
3 to 10 kΩ
3 to 10 kΩ
V
V
DD
DD
User’s Manual U18371EJ1V0UM
1 to 10 kΩ
1 to 10 kΩ
1 to
1 to
1 to
10 kΩ
10 kΩ
10 kΩ
V
V
DD
DD
Note 3
Note 3
10 kΩ
10 kΩ
V
V
Clock
Clock
circuit
circuit
DD
DD
1 kΩ
1 kΩ
GND
GND
_RESET
_RESET
TxD
TxD
V
V
RxD
RxD
X1
X1
X2
X2
FLMD1
FLMD1
FLMD0
FLMD0
Port X
Port X
Target device
Target device
Reset connector
Reset connector
RESET signal
RESET signal
DD
DD
Note 5
Note 5
P31
P31
1 to 10 kΩ
1 to 10 kΩ
57
Related parts for QB-MINI2-EE
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
16/8 bit single-chip microcomputer
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual audio power amp circuit
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual comparator
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
MOS type composite field effect transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
50 V/100 mA FET array incorporating 2 N-ch MOSFETs
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Twin transistors equipped with different model chips(6P small MM)
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Bipolar analog integrated circuit
Manufacturer:
NEC
Datasheet: