QB-MINI2-EE NEC, QB-MINI2-EE Datasheet - Page 91
QB-MINI2-EE
Manufacturer Part Number
QB-MINI2-EE
Description
EMULATOR, PROGRAMMER, MINICUBE2
Manufacturer
NEC
Type
Debug Emulatorr
Datasheet
1.QB-MINI2-EE.pdf
(169 pages)
Specifications of QB-MINI2-EE
Svhc
No SVHC (18-Jun-2010)
Mcu Supported Families
MINICUBE2
Silicon Family Name
V850, 78K0R, 78K0S
Ic Product Type
On-Chip Debug Emulator
Kit Contents
MINICUBE2, USB Cable, Target Cable, 78K0-OCD Board
Features
On-Chip Debugging, Flash Memory Programming,
- Current page: 91 of 169
- Download datasheet (6Mb)
4.3.3
(1) Preparation and installation of software
(2) Switch setting
Caution Do not change the switch setting while the USB cable is connected.
(3) Connecting the target system
This section describes the system startup procedure. Observe the following order.
The following software is required to perform flash programming.
of software, refer to the setup manual supplied with MINICUBE2.
Set the mode select switch to ″ M2 ″ . Set the power select switch by referring to the following table.
Connect MINICUBE2 to the target system as shown in Figure 4-35, before the power to the target system is
turned on. When the power select switch is set to ″ T ″ , the step of (4) Connecting the USB cable can be
performed before this step.
System startup procedure
Note The maximum rating of the current is 100 mA, so do not use MINICUBE2 with the target system with
3
5
T
• QB-Programmer
• USB driver
• Parameter file
Setting
the higher current rating. The power is always supplied after MINICUBE2 is connected to the host
machine.
CHAPTER 4
Target system
Target system
3 V is supplied from MINICUBE2 to the target system
5 V is supplied from MINICUBE2 to the target system
Power supply of the target system is used.
MINICUBE2 detects the power for the target system.
The detected power is also used as the power supply for the communication interface.
Figure 4-35. Connecting MINICUBE2 to Target System
Table 4-11. Setting of Power Select Switch
HOW TO USE MINICUBE2 WITH 78K0 MICROCONTROLLER
User’s Manual U18371EJ1V0UM
16-pin target cable
16-pin target cable
Description
Note
For details on preparation and installation
Note
.
.
MINICUBE2
MINICUBE2
91
Related parts for QB-MINI2-EE
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
16/8 bit single-chip microcomputer
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual audio power amp circuit
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Dual comparator
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
MOS type composite field effect transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
50 V/100 mA FET array incorporating 2 N-ch MOSFETs
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
6-pin small MM high-frequency double transistor
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Twin transistors equipped with different model chips(6P small MM)
Manufacturer:
NEC
Datasheet:
Part Number:
Description:
Bipolar analog integrated circuit
Manufacturer:
NEC
Datasheet: