DS33R11 Maxim Integrated Products, DS33R11 Datasheet - Page 100
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
DS33R11
Manufacturer Part Number
DS33R11
Description
Network Controller & Processor ICs Ethernet Mapper with Integrated T1-E1-J1
Manufacturer
Maxim Integrated Products
Datasheet
1.DS33R11.pdf
(344 pages)
Specifications of DS33R11
Product
Framer
Number Of Transceivers
1
Supply Voltage (max)
1.89 V, 3.465 V
Supply Voltage (min)
1.71 V, 3.135 V
Supply Current (max)
100 mA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Package / Case
BGA
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS33R11
Manufacturer:
NSC
Quantity:
2 877
Part Number:
DS33R11
Manufacturer:
DALLAS
Quantity:
20 000
Part Number:
DS33R11+
Manufacturer:
DALLAS
Quantity:
20 000
Company:
Part Number:
DS33R11+CJ2
Manufacturer:
Maxim Integrated
Quantity:
10 000
- Current page: 100 of 344
- Download datasheet (12Mb)
DS33R11 Ethernet Mapper with Integrated T1/E1/J1 Transceiver
10.20 Line Interface Unit (LIU)
The LIU contains three sections: the receiver that handles clock and data recovery, the transmitter that
waveshapes and drives the T1 line, and the jitter attenuator. These three sections are controlled by the line
interface control registers (LIC1–LIC4), which are described in the following sections. The LIU has its own T1/E1
mode-select bit and can operate independently of the framer function.
The transceiver can switch between T1 or E1 networks without changing external components on the transmit or
receive side.
Figure 10-7
shows a network connection using minimal components. In this configuration, the
transceiver can connect to T1, J1, or E1 (75Ω or 120Ω) without component changes. The receiver can adjust the
120Ω termination to 100Ω or 75Ω. The transmitter can adjust its output impedance to provide high return-loss
characteristics for 120Ω, 100Ω, and 75Ω lines. Other components can be added to this configuration to meet
safety and network protection requirements (Section 10.24).
10.20.1 LIU Operation
The analog AMI/HDB3 waveform off the E1 line or the AMI/B8ZS waveform off of the T1 line is transformer-
coupled into the RTIP and RRING pins of the device. The user has the option to use internal termination, software
selectable for 75Ω/100Ω/120Ω applications, or external termination. The LIU recovers clock and data from the
analog signal and passes it through the jitter-attenuation mux outputting the received line clock at RDCLKO and
bipolar or NRZ data at RPOSO and RNEGO. The transceiver contains an active filter that reconstructs the analog-
received signal for the nonlinear losses that occur in transmission. The receive circuitry also is configurable for
various monitor applications. The device has a usable receive sensitivity of 0dB to -43dB for E1 and 0dB to -36dB
for T1, which allow the device to operate on 0.63mm (22AWG) cables up to 2.5km (E1) and 6k feet (T1) in length.
Data input at TPOSI and TNEGI is sent through the jitter-attenuation mux to the waveshaping circuitry and line
driver. The transceiver drives the E1 or T1 line from the TTIP and TRING pins through a coupling transformer. The
line driver can handle both CEPT 30/ISDN-PRI lines for E1 and long-haul (CSU) or short-haul (DSX-1) lines for T1.
10.20.2 Receiver
The receiver contains a digital clock recovery system. The device couples to the receive E1 or T1 twisted pair (or
coaxial cable in 75Ω E1 applications) through a 1:1 transformer. See
Table 10-13
for transformer details. The
device has the option of using software-selectable termination requiring only a single fixed pair of termination
resistors.
The transceiver’s LIU is designed to be fully software selectable for E1 and T1, requiring no change to any external
resistors for the receive side. The receive side allows the user to configure the transceiver for 75Ω, 100Ω, or 120Ω
receive termination by setting the RT1 (TR.LIC4.1) and RT0 (TR.LIC4.0) bits. When using the internal termination
feature, the resistors labeled R in
Figure 10-7
should be 60Ω each. If external termination is used, RT1 and RT0
should be set to 0 and the resistors labeled R in
Figure 10-7
should be 37.5Ω, 50Ω, or 60Ω each, depending on
the line impedance.
There are two ranges of user-selectable receive sensitivity for T1 and E1. The EGL bit of TR.LIC1 (TR.LIC1.4)
selects the full or limited sensitivity. The resultant E1 or T1 clock derived from MCLK is multiplied by 16 through an
internal PLL and fed to the clock recovery system. The clock recovery system uses the clock from the PLL circuit to
form a 16-times over-sampler that is used to recover the clock and data. This over-sampling technique offers
outstanding performance to meet jitter tolerance specifications shown in
Figure
10-10.
Normally, the clock that is output at the RCLKO pin is the recovered clock from the E1 AMI/HDB3 or T1 AMI/B8ZS
waveform presented at the RTIP and RRING inputs. If the jitter attenuator is placed in the receive path (as is the
case in most applications), the jitter attenuator restores the RCLKO to an approximate 50% duty cycle. If the jitter
attenuator is either placed in the transmit path or is disabled, the RCLKO output can exhibit slightly shorter high
cycles of the clock. This is because of the highly over-sampled digital-clock recovery circuitry. See the Receive AC
Timing Characteristics in Section
13.9
for more details. When no signal is present at RTIP and RRING, a receive
carrier loss (RCL) condition occurs and the RCLKO is derived from the JACLK source.
100 of 344
Related parts for DS33R11
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![MAX7528KCWP](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX3261CCJ](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX3263CAG](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX8809AETL+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
![MAX1535CETJ+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
![DS2741N+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
![MAX13450EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX13451EAUD+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
![MAX17497BATE+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
QFN 16/A/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
![MAX17502FATB+T](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
![MAX1978EVKIT](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
![MAX2606EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
![MAX2608EUT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
![MAX2831EVKIT+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
![MAX4888CETI+](/images/manufacturer_photos/0/4/417/maxim_integrated_products_tmb.jpg)
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: