DS33R11 Maxim Integrated Products, DS33R11 Datasheet - Page 77
DS33R11
Manufacturer Part Number
DS33R11
Description
Network Controller & Processor ICs Ethernet Mapper with Integrated T1-E1-J1
Manufacturer
Maxim Integrated Products
Datasheet
1.DS33R11.pdf
(344 pages)
Specifications of DS33R11
Product
Framer
Number Of Transceivers
1
Supply Voltage (max)
1.89 V, 3.465 V
Supply Voltage (min)
1.71 V, 3.135 V
Supply Current (max)
100 mA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Package / Case
BGA
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS33R11
Manufacturer:
NSC
Quantity:
2 877
Part Number:
DS33R11
Manufacturer:
DALLAS
Quantity:
20 000
Part Number:
DS33R11+
Manufacturer:
DALLAS
Quantity:
20 000
Company:
Part Number:
DS33R11+CJ2
Manufacturer:
Maxim Integrated
Quantity:
10 000
- Current page: 77 of 344
- Download datasheet (12Mb)
10.5.1 Automatic Alarm Generation
The device can be programmed to automatically transmit AIS or remote alarm. When automatic AIS generation is
enabled (TR.E1TCR2.1 = 1), the device monitors the receive-side framer to determine if any of the following
conditions are present: loss-of-receive frame synchronization, AIS alarm (all ones) reception, or loss-of-receive
carrier (or signal). The framer forces either an AIS or remote alarm if any one or more of these conditions is
present.
When automatic RAI generation is enabled (TR.E1TCR2.0 = 1), the framer monitors the receive side to determine
if any of the following conditions are present: loss-of-receive-frame synchronization, AIS alarm (all ones) reception,
loss-of-receive carrier (or signal), or if CRC4 multiframe synchronization cannot be found within 128ms of FAS
synchronization (if CRC4 is enabled). If any one or more of these conditions is present, then the framer transmits
an RAI alarm. RAI generation conforms to ETS 300 011 specifications and a constant remote alarm is transmitted
if the device cannot find CRC4 multiframe synchronization within 400ms as per G.706.
Note: It is an invalid state to have both automatic AIS generation and automatic remote alarm generation enabled
at the same time.
Table 10-4. E1 Alarm Criteria
10.6 Per-Channel Loopback
The per-channel loopback registers (PCLRs) determine which channels (if any) from the backplane should be
replaced with the data from the receive side or, i.e., off of the T1 or E1 line. If this loopback is enabled, then
transmit and receive clocks and frame syncs must be synchronized. One method to accomplish this is to connect
RCLKO to TCLKT and RFSYNC to TSYNC. There are no restrictions on which channels can be looped back or on
how many channels can be looped back.
Each of the bit positions in the per-channel loopback registers (TR.PCLR1/TR.PCLR2/TR.PCLR3/TR.PCLR4)
represents a DS0 channel in the outgoing frame. When these bits are set to a 1, data from the corresponding
receive channel replaces the data on TSERI for that channel.
V52LNK
ALARM
RDMA
RLOS
RUA1
RRA
RCL
An RLOS condition exists on power-up
prior to initial synchronization, when a
resync criteria has been met, or when a
manual resync has been initiated by
TR.E1RCR1.0
255 or 2048 consecutive 0s received as
determined by TR.E1RCR2.0
Bit 3 of nonalign frame set to 1 for three
consecutive occasions
Fewer than three 0s in two frames (512
bits)
Bit 6 of time slot 16 in frame 0 has been set
for two consecutive multiframes
Two out of three Sa7 bits are 0
SET CRITERIA
77 of 344
At least 32 1s in 255-bit times
are received
Bit 3 of nonalign frame set to
0 for three consecutive
occasions
More than two 0s in two
frames (512 bits)
CLEAR CRITERIA
SPECIFICATION
G.775/G.962
1.6.1.2
O.162
O.162
G.965
2.1.4
ITU
Related parts for DS33R11
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: