MT46H64M16LFCK-75:A TR Micron Technology Inc, MT46H64M16LFCK-75:A TR Datasheet - Page 39
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT46H64M16LFCK-75:A TR
Manufacturer Part Number
MT46H64M16LFCK-75:A TR
Description
Manufacturer
Micron Technology Inc
Type
DDR SDRAMr
Datasheet
1.MT46H64M16LFCK-75A_TR.pdf
(96 pages)
Specifications of MT46H64M16LFCK-75:A TR
Organization
64Mx16
Density
1Gb
Address Bus
14b
Access Time (max)
6.5/6ns
Maximum Clock Rate
133MHz
Operating Supply Voltage (typ)
1.8V
Package Type
VFBGA
Operating Temp Range
0C to 70C
Operating Supply Voltage (max)
1.95V
Operating Supply Voltage (min)
1.7V
Supply Current
105mA
Pin Count
60
Mounting
Surface Mount
Operating Temperature Classification
Commercial
Lead Free Status / RoHS Status
Compliant
Truth Tables
Table 16: Truth Table – Current State Bank n – Command to Bank n
Notes 1–6 apply to all parameters in this table
PDF: 09005aef82ce3074
1gb_ddr_mobile_sdram_t48m.pdf - Rev. L 04/10 EN
Current State
Any
Idle
Row active
Read (auto pre-
charge disabled)
Write (auto pre-
charge disabled)
CS#
Notes:
H
L
L
L
L
L
L
L
L
L
L
L
L
L
L
RAS#
1. This table applies when CKE
2. This table is bank-specific, except where noted (for example, the current state is for a
3. Current state definitions:
4. The states listed below must not be interrupted by a command issued to the same bank.
X
H
H
H
H
H
H
H
H
L
L
L
L
L
L
the previous state was self refresh), after
down, or a full initialization if the previous state was deep power-down).
specific bank and the commands shown are supported for that bank when in that state).
Exceptions are covered in the notes below.
Idle: The bank has been precharged, and
Row active: A row in the bank has been activated, and
accesses and no register accesses are in progress.
Read: A READ burst has been initiated with auto precharge disabled and has not yet
terminated or been terminated.
Write: A WRITE burst has been initiated with auto precharge disabled and has not yet
terminated or been terminated.
COMMAND INHIBIT or NOP commands, or supported commands to the other bank,
must be issued on any clock edge occurring during these states. Supported commands to
any other bank are determined by that bank’s current state.
Precharging: Starts with registration of a PRECHARGE command and ends when
met. After
Row activating: Starts with registration of an ACTIVE command and ends when
met. After
CAS#
X
H
H
H
H
H
H
L
L
L
L
L
L
L
L
t
t
RP is met, the bank will be in the idle state.
RCD is met, the bank will be in the row active state.
WE# Command/Action
X
H
H
H
H
H
H
L
L
L
L
L
L
L
L
DESELECT (NOP/continue previous operation)
NO OPERATION (NOP/continue previous operation)
ACTIVE (select and activate row)
AUTO REFRESH
LOAD MODE REGISTER
READ (select column and start READ burst)
WRITE (select column and start WRITE burst)
PRECHARGE (deactivate row in bank or banks)
READ (select column and start new READ burst)
WRITE (select column and start WRITE burst)
PRECHARGE (truncate READ burst, start PRECHARGE)
BURST TERMINATE
READ (select column and start READ burst)
WRITE (select column and start new WRITE burst)
PRECHARGE (truncate WRITE burst, start PRECHARGE)
39
n - 1
was HIGH, CKE
1Gb: x16, x32 Mobile LPDDR SDRAM
Micron Technology, Inc. reserves the right to change products or specifications without notice.
t
XP has been met (if the previous state was power-
t
RP has been met.
n
is HIGH and after
t
RCD has been met. No data bursts/
© 2007 Micron Technology, Inc. All rights reserved.
t
XSR has been met (if
Truth Tables
Notes
t
10, 12
10, 11
RCD is
8, 11
t
RP is
10
10
10
10
7
7
8
8
9