EP3C40F484C8N Altera, EP3C40F484C8N Datasheet - Page 157

• Manufacturer Part Number: EP3C40F484C8N
• Description: IC CYCLONE III FPGA 40K 484FBGA
• Manufacturer: Altera
• Series: Cyclone® IIIr

Specifications of EP3C40F484C8N

• Number Of Logic Elements/cells: 39600
• Number Of Labs/clbs: 2475
• Total Ram Bits: 1161216
• Number Of I /o: 331
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 484-FBGA
• Family Name: Cyclone III
• Number Of Logic Blocks/elements: 39600
• # I/os (max): 331
• Frequency (max): 402MHz
• Process Technology: 65nm
• Operating Supply Voltage (typ): 1.2V
• Logic Cells: 39600
• Ram Bits: 1161216
• Operating Supply Voltage (min): 1.15V
• Operating Supply Voltage (max): 1.25V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 484
• Package Type: FBGA
• No. Of Logic Blocks: 2475
• Family Type: Cyclone III
• No. Of I/o's: 331
• I/o Supply Voltage: 3.3V
• Operating Frequency Max: 402MHz
• Operating Temperature Range: 0°C To +85°C
• Rohs Compliant: Yes
• For Use With: 544-2601 - KIT DEV CYCLONE III LS EP3CLS200544-2411 - KIT DEV NIOS II CYCLONE III ED.
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 544-2492

Chapter 8: External Memory Interfaces in the Cyclone III Device Family
Cyclone III Device Family Memory Interfaces Features
Figure 8–6. Extending the OE Disable by Half a Clock Cycle for a Write Transaction
Note to
(1) The waveform reflects the software simulation result. The OE signal is an active low on the device. However, the Quartus II software implements
OCT
PLL
© January 2010 Altera Corporation
the signal as an active high and automatically adds an inverter before the A
Figure
8–6:
f
f
1
from System Clock)
(outclock for DQS)
-90 phase shifted
(from logic array)
(from logic array)
(from logic array)
(from logic array)
(outclock for DQ,
Figure 8–6
high-impedance state by half a clock cycle during a write operation.
o
Cyclone III device family supports calibrated on-chip series termination (R
both vertical and horizontal I/O banks. To use the calibrated OCT, you must use the
RUP and RDN pins for each R
each OCT calibration block to calibrate one type of termination with the same V
that given side.
For more information about Cyclone III device family OCT calibration block, refer to
the
When interfacing with external memory, the PLL is used to generate the memory
system clock, the write clock, the capture clock and the logic-core clock. The system
clock generates the DQS write signals, commands, and addresses. The write-clock is
shifted by -90° from the system clock and generates the DQ signals during writes. You
can use the PLL reconfiguration feature to calibrate the read-capture phase shift to
balance the setup and hold margins.
The PLL is instantiated in the ALTMEMPHY megafunction. All outputs of the PLL are
used when the ALTMEMPHY megafunction is instantiated to interface with external
memories.
For more information about the usage of PLL outputs by the ALTMEMPHY
megafunction, refer to
System clock
OE for DQS
Write Clock
OE for DQ
datain_h
datain_I
Cyclone III Device I/O Features
DQS
DQ
shows how the second output enable register extends the DQS
90
o
Literature: External Memory
a Clock
by Half
Delay
Cycle
S
OCT control block (one for each side). You can use
chapter.
Preamble
OE
register D input.
D1
D0
D0
D1
Interfaces.
D3
D2
D2
(Note 1)
Cyclone III Device Handbook, Volume 1
D3
Postamble
S
OCT) in
CCIO
8–13
for