LAN9420I-NU SMSC, LAN9420I-NU Datasheet - Page 119

• Manufacturer Part Number: LAN9420I-NU
• Description: IC ETHERNET CTRLR SGL 128VTQFP
• Manufacturer: SMSC
• Type: Single Chip MAC and PHY Controllerr

Specifications of LAN9420I-NU

• Controller Type: Ethernet Controller
• Interface: PCI
• Voltage - Supply: 3 V ~ 3.6 V
• Current - Supply: 145mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 128-TQFP, 128-VQFP
• Product: Ethernet Controllers
• Number Of Transceivers: 1
• Standard Supported: 802.3, 802.3u
• Data Rate: 10 MB, 100 MB
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 1.6 V
• Maximum Operating Temperature: + 85 C
• Ethernet Connection Type: 10/100 Base-T
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 638-1085

Single-Chip Ethernet Controller with HP Auto-MDIX Support and PCI Interface
Datasheet
SMSC LAN9420/LAN9420i
4.4.1
30-24
BITS
31
23
22
21
20
19
18
17
16
Receive All Mode (RXALL)
When set, all incoming packets will be received and passed on to the
address filtering function for processing of the selected filtering mode on the
received frame. Address filtering then occurs and is reported in Receive
Status. When reset, only frames that pass Destination Address filtering will
be sent to the Application.
RESERVED
Disable Receive Own (RCVOWN)
When set, the MAC disables the reception of frames when TXEN is
asserted. The MAC blocks the transmitted frame on the receive path. When
reset, the MAC receives all packets the PHY gives, including those
transmitted by the MAC.This bit should be reset when the Full Duplex Mode
bit is set.
RESERVED
Loopback operation Mode (LOOPBK)
Selects the loop back operation modes for the MAC. This is only for full
duplex mode
0 - Normal. No feedback
1 - Internal through MII
In internal loopback mode, the TX frame is received by the Internal MII
interface, and sent back to the MAC without being sent to the PHY.
Note:
Full Duplex Mode (FDPX)
When set, the MAC operates in Full-Duplex mode, in which it can transmit
and receive simultaneously.
Pass All Multicast (MCPAS)
When set, indicates that all incoming frames with a Multicast destination
address (first bit in the destination address field is 1) are received. Incoming
frames with physical address (Individual Address/Unicast) destinations are
filtered and received only if the address matches the MAC Address.
Promiscuous Mode (PRMS)
When set, indicates that any incoming frame is received regardless of its
destination address.
Inverse filtering (INVFILT)
When set, the address check Function operates in Inverse filtering mode.
This is valid only during Perfect filtering mode.
Pass Bad Frames (PASSBAD)
When set, all incoming frames that passed address filtering are received,
including runt frames and collided frames.
MAC Control Register (MAC_CR)
This register establishes the RX and TX operating modes and includes controls for address filtering
and packet filtering.
Offset:
When enabling or disabling the loopback mode it can take up to
10μs for the mode change to occur. The transmitter and receiver
must be stopped and disabled when modifying the LOOPBK bit.
The transmitter or receiver should not be enabled within10μs of
modifying the LOOPBK bit.
DESCRIPTION
0080h
DATASHEET
119
Size:
32 bits
TYPE
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
RO
RO
Revision 1.4 (12-17-08)
DEFAULT
0b
0b
0b
0b
0b
1b
0b
0b
-
-