DP83848TSQ/NOPB National Semiconductor, DP83848TSQ/NOPB Datasheet - Page 17

• Manufacturer Part Number: DP83848TSQ/NOPB
• Description: IC TXRX ETHERNET PHYTER 40-LLP
• Manufacturer: National Semiconductor
• Type: Transceiverr

Specifications of DP83848TSQ/NOPB

• Number Of Drivers/receivers: 1/1
• Protocol: Ethernet
• Voltage - Supply: 3 V ~ 3.6 V
• Mounting Type: Surface Mount
• Package / Case: 40-LLP
• Data Rate: 100Mbps
• Supply Voltage Range: 3V To 3.6V
• Logic Case Style: LLP
• No. Of Pins: 40
• Operating Temperature Range: -40°C To +85°C
• Msl: MSL 2 - 1 Year
• Filter Terminals: SMD
• Rohs Compliant: Yes
• Data Rate Max: 10Mbps
• Driver Case Style: LLP
• For Use With: DP83848T-MAU-EK - BOARD EVALUATION DP83848T
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: DP83848TSQTR

2.3 PHY Address
The 5 PHY address inputs pins are shared with the
RXD[3:0] pins and COL pin as shown below.
The DP83848T can be set to respond to any of 32 possible
PHY addresses via strap pins. The information is latched
into the PHYCR register (address 19h, bits [4:0]) at device
power-up and hardware reset. The PHY Address pins are
shared with the RXD and COL pins. Each DP83848T or
port sharing an MDIO bus in a system must have a unique
physical address.
The DP83848T supports PHY Address strapping values 0
(<00000>) through 31 (<11111>). Strapping PHY Address
0 puts the part into Isolate Mode. It should also be noted
that selecting PHY Address 0 via an MDIO write to PHYCR
will not put the device in Isolate Mode. See Section 2.3.1
for more information.
For further detail relating to the latch-in timing requirements
of the PHY Address pins, as well as the other hardware
configuration pins, refer to the Reset summary in
Section 6.0.
Pin #
35
36
37
38
39
Table 2. PHY Address Mapping
PHYAD Function
PHYAD0
PHYAD1
PHYAD2
PHYAD3
PHYAD4
RXD Function
Figure 2. PHYAD Strapping Example
RXD_0
RXD_1
RXD_2
RXD_3
COL
17
Since the PHYAD[0] pin has weak internal pull-up resistor
and PHYAD[4:1] pins have weak internal pull-down resis-
tors, the default setting for the PHY address is 00001
(01h).
Refer to Figure 2 for an example of a PHYAD connection to
external components. In this example, the PHYAD strap-
ping results in address 00011 (03h).
2.3.1 MII Isolate Mode
The DP83848T can be put into MII Isolate mode by writing
to bit 10 of the BMCR register or by strapping in Physical
Address 0. It should be noted that selecting Physical
Address 0 via an MDIO write to PHYCR will not put the
device in the MII isolate mode.
When in the MII isolate mode, the DP83848T does not
respond to packet data present at TXD[3:0], TX_EN inputs
and presents a high impedance on the TX_CLK, RX_CLK,
RX_DV, RX_ER, RXD[3:0], COL, and CRS outputs. When
in Isolate mode, the DP83848T will continue to respond to
all management transactions.
While in Isolate mode, the PMD output pair will not transmit
packet data but will continue to source 100BASE-TX
scrambled idles or 10BASE-T normal link pulses.
The DP83848T can Auto-Negotiate or parallel detect to a
specific technology depending on the receive signal at the
PMD input pair. A valid link can be established for the
receiver even when the DP83848T is in Isolate mode.
VCC
www.national.com