MRF89XAT-I/MQ Microchip Technology, MRF89XAT-I/MQ Datasheet - Page 68

• Manufacturer Part Number: MRF89XAT-I/MQ
• Description: RF ISM BAND TXRX 32 QFN
• Manufacturer: Microchip Technology
• Series: -r

Specifications of MRF89XAT-I/MQ

• Frequency: 863MHz ~ 870MHz, 902MHz ~ 928MHz, 950MHz ~ 960MHz
• Data Rate - Maximum: 200 kbps
• Modulation Or Protocol: FSK, OOK
• Applications: ISM
• Power - Output: 12.5dBm
• Sensitivity: -113dBm
• Voltage - Supply: 2.1 V ~ 3.6 V
• Current - Receiving: 3mA
• Current - Transmitting: 25mA
• Data Interface: PCB, Surface Mount
• Memory Size: *
• Antenna Connector: PCB, Surface Mount
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Rf Ic Case Style: QFN
• No. Of Pins: 32
• Svhc: No SVHC (20-Jun-2011)
• Rohs Compliant: Yes
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: MRF89XAT-I/MQTR

3.4.6
The center frequency, f
chart in Figure 3-8 illustrates the receiver bandwidth
when the BUTFILV<3:0> bits (FILCREG<3:0>) are
changed when the polyphase filter is activated.
Table 4-2 in Section 4.6 “Crystal Specification and
Selection Guidelines” suggests a few filter settings in
OOK mode along with the corresponding passive filter
bandwidth and the accepted tolerance on the crystal
reference.
FIGURE 3-8:
3.4.7.2
In OOK mode, the RSSI evaluates the signal strength
by sampling I(t) and Q(t) signals 16 times in each
period of the chosen IF2 frequency (refer to
Section 2.10.1 “Receiver Architecture”). In FSK
mode, the signals are sampled 16 times in each f
period, f
companion transmitter. An average is then performed
over a sliding window of 16 samples. Therefore, the
RSSI output register RSTSREG (RSSIVAL<7:0>) is
updated 16 times in each f
DS70622B-page 68
MRF89XA
450
400
350
300
250
200
150
100
50
0
dev
0
CHANNEL FILTERS SETTING IN
OOK MODE
being the frequency deviation of the
Acquisition Time
ACTUAL BW OF POLYPHASE FILTER
o
2
, is always set to 100 kHz. The
dev
or IF2 period.
4
Polyphase Filter's BW, OOK
6
Val BUTFILV<3:0> [d]
POLCFV<3:0> = 0011
Preliminary
dev
8
3.4.7
After filtering, the In-phase and Quadrature signals are
amplified by a chain of 11 amplifiers, each with 6dB
gain. The outputs of these amplifiers are used to
evaluate the RSSI.
3.4.7.1
When the RSSI resolution is 0.5 dB, the absolute
accuracy is not expected to be better than ±3dB due to
process and external component variation. Higher
accuracy
measurements will require additional calibration.
The following settings are recommended:
• FSK Mode: Ensure that the f
• OOK reception: Ensure that the f
described in the FDEVREG register (Register 2-3)
through the FDVAL<7:0> bits) remains consistent
with
companion transmitter.
described in the FDEVREG register (Register 2-3)
through the FDVAL<7:0> bits)) is equal with the fre-
quency of the I(t) and Q(t) signals (that is, the sec-
ond Intermediate Frequency, IF2, of the receiver).
Note that this equals f
polyphase filter.
the
10
RECEIVED SIGNAL STRENGTH
(RSSI)
while
Resolution and Accuracy
actual
performing
12
frequency
© 2010 Microchip Technology Inc.
o
, the center frequency of the
Actual
BW
deviation
14
dev
absolute
dev
Theoretical
BW
parameter (as
parameter (as
of
16
RSSI
the