AT90PWM3B Atmel Corporation, AT90PWM3B Datasheet - Page 171

• Manufacturer Part Number: AT90PWM3B
• Manufacturer: Atmel Corporation

Specifications of AT90PWM3B

• Flash (kbytes): 8 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 27
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 3
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 5
• Output Compare Channels: 16
• Input Capture Channels: 1
• Pwm Channels: 12
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

16.26.4
16.26.5
16.26.6
16.26.7
4317J–AVR–08/10
PSC2 Interrupt Mask Register – PIM2
PSC0 Interrupt Flag Register – PIFR0
PSC1 Interrupt Flag Register – PIFR1
PSC2 Interrupt Flag Register – PIFR2
Bit
Read/Write
Initial Value
• Bit 5 – PSEIEn : PSC n Synchro Error Interrupt Enable
When this bit is set, the PSEIn bit (if set) generate an interrupt.
• Bit 4 – PEVEnB : PSC n External Event B Interrupt Enable
When this bit is set, an external event which can generates a capture from Retrigger/Fault block
B generates also an interrupt.
• Bit 3 – PEVEnA : PSC n External Event A Interrupt Enable
When this bit is set, an external event which can generates a capture from Retrigger/Fault block
A generates also an interrupt.
• Bit 0 – PEOPEn : PSC n End Of Cycle Interrupt Enable
When this bit is set, an interrupt is generated when PSC reaches the end of the whole cycle.
Bit
Read/Write
Initial Value
Bit
Read/Write
Initial Value
Bit
Read/Write
Initial Value
• Bit 7 – POACnB : PSC n Output B Activity (not implemented on AT90PWM2/3)
This bit is set by hardware each time the output PSCOUTn1 changes from 0 to 1 or from 1 to 0.
Must be cleared by software by writing a one to its location.
This feature is useful to detect that a PSC output doesn’t change due to a freezen external input
signal.
• Bit 6 – POACnA : PSC n Output A Activity (not implemented on AT90PWM2/3)
This bit is set by hardware each time the output PSCOUTn0 changes from 0 to 1 or from 1 to 0.
Must be cleared by software by writing a one to its location.
POAC0B
POAC1B
POAC2B
R
R
R
R
7
0
7
0
7
0
7
0
-
POAC0A
POAC1A
POAC2A
R
R
R
R
6
0
6
0
6
0
6
0
-
PSEIE2
PSEI0
PSEI1
PSEI2
R/W
R/W
R/W
R/W
5
0
5
0
5
0
5
0
PEVE2B
PEV0B
PEV1B
PEV2B
R/W
R/W
R/W
R/W
4
0
4
0
4
0
4
0
PEVE2A
PEV0A
PEV1A
PEV2A
R/W
R/W
R/W
R/W
3
0
3
0
3
0
3
0
AT90PWM2/3/2B/3B
PRN01
PRN11
PRN21
R
R
R
R
2
0
2
0
2
0
2
0
-
PRN00
PRN10
PRN20
R
R
R
R
1
0
1
0
1
0
1
0
-
PEOPE2
PEOP2
PEOP1
PEOP2
R/W
R/W
R/W
R/W
0
0
0
0
0
0
0
0
PIFR0
PIFR1
PIFR2
PIM2
171