AT90PWM81 Atmel Corporation, AT90PWM81 Datasheet - Page 38
AT90PWM81
Manufacturer Part Number
AT90PWM81
Description
Manufacturer
Atmel Corporation
Datasheet
1.AT90PWM161.pdf
(325 pages)
Specifications of AT90PWM81
Flash (kbytes)
8 Kbytes
Pin Count
20
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
Hardware Qtouch Acquisition
No
Max I/o Pins
20
Ext Interrupts
3
Usb Speed
No
Usb Interface
No
Spi
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
11
Adc Resolution (bits)
10
Adc Speed (ksps)
125
Analog Comparators
3
Resistive Touch Screen
No
Dac Channels
1
Dac Resolution (bits)
10
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
0.25
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 125
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
1
Output Compare Channels
8
Input Capture Channels
1
Pwm Channels
6
32khz Rtc
No
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT90PWM81-16MF
Manufacturer:
Atmel
Quantity:
3 118
Company:
Part Number:
AT90PWM81-16MN
Manufacturer:
Atmel
Quantity:
2 446
Company:
Part Number:
AT90PWM81-16SF
Manufacturer:
Atmel
Quantity:
2 428
Company:
Part Number:
AT90PWM81-16SN
Manufacturer:
Atmel
Quantity:
1 500
- Current page: 38 of 325
- Download datasheet (6Mb)
5.4
5.4.1
5.4.2
5.5
5.5.1
38
System Clock Prescaler
Register Description
AT90PWM81
Features
Switching Time
OSCCAL – Oscillator Calibration Register
The AT90PWM81 system clock can be divided by setting the Clock Prescaler Register – CLKPR. This
feature can be used to decrease power consumption when the requirement for processing power is low.
This can be used with all clock source options, and it will affect the clock frequency of the CPU and all
synchronous peripherals. clk
10 on page
When switching between prescaler settings, the System Clock Prescaler ensures that no glitches occur in
the clock system and that no intermediate frequency is higher than neither the clock frequency corre-
sponding to the previous setting, nor the clock frequency corresponding to the new setting.
The ripple counter that implements the prescaler runs at the frequency of the undivided clock, which may
be faster than the CPU’s clock frequency. Hence, it is not possible to determine the state of the prescaler –
even if it were readable, and the exact time it takes to switch from one clock division to another cannot be
exactly predicted.
From the time the CLKPS values are written, it takes between T1 + T2 and T1 + 2*T2 before the new
clock frequency is active. In this interval, 2 active clock edges are produced. Here, T1 is the previous
clock period, and T2 is the period corresponding to the new prescaler setting.
• Bits 7:0 – CAL7:0: Oscillator Calibration Value
The Oscillator Calibration Register is used to trim the Calibrated Internal RC Oscillator to remove process
variations from the oscillator frequency. The factory-calibrated value is automatically written to this regis-
ter during chip reset, giving an oscillator frequency of 8.0 MHz at 25°C. The application software can
write this register to change the oscillator frequency. The oscillator can be calibrated to any frequency in
the range 7.6 - 8.4 MHz within ± 1% accuracy. Calibration outside that range is not guaranteed.
Note that this oscillator is used to time EEPROM and Flash write accesses, and these write times will be
affected accordingly. If the EEPROM or Flash are written, do not calibrate to more than 8.8 MHz. Other-
wise, the EEPROM or Flash write may fail.
The CAL7..0 bits are used to tune the frequency within the selected range. A setting of 0x00 gives the
lowest frequency in that range, and a setting of 0x7F gives the highest frequency in the range. Increment-
ing CAL7..0 by 1 will give a frequency increment of less than 0.5% in the frequency range 7.6 - 8.4 MHz.
Bit
Read/Write
Initial Value
39.
CAL7
R/W
7
CAL6
R/W
I/O
6
, clk
ADC
CAL5
R/W
, clk
5
Device Specific Calibration Value
CPU
, and clk
CAL4
R/W
4
FLASH
CAL3
R/W
3
are divided by a factor as shown in
CAL2
R/W
2
CAL1
R/W
1
CAL0
R/W
0
7734P–AVR–08/10
OSCCAL
Table 5-
Related parts for AT90PWM81
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: