ATmega6450P Atmel Corporation, ATmega6450P Datasheet - Page 284

• Manufacturer Part Number: ATmega6450P
• Manufacturer: Atmel Corporation

Specifications of ATmega6450P

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 25
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

27.2
8285D–AVR–06/11
Fuse Bits
ATmega165A/PA/325A/PA/3250A/PA/645A/P/6450A/P
Table 27-2.
Notes:
The ATmega165A/165PA/325A/325PA/3250A/3250PA/645A/645P/6450A/6450P has three
Fuse bytes.
they are mapped into the Fuse bytes. Note that the fuses are read as logical zero, “0”, if they are
programmed.
Table 27-3.
Notes:
–
–
–
–
BODLEVEL2
BODLEVEL1
BODLEVEL0
RSTDISBL
Fuse Low Byte
BLB1 Mode
1
2
3
4
1. Program the Fuse bits and Boot Lock bits before programming the LB1 and LB2.
2. “1” means unprogrammed, “0” means programmed
1. See
2. Port G, PG5 is input only. Pull-up is always on.
Memory Lock Bits
(2)
84.
Table 27-3
(1)
(1)
(1)
Lock Bit Protection Modes
Extended Fuse Byte
Table 28-16 on page 327
BLB12
1
1
0
0
Bit No
7
6
5
4
3
2
1
0
-
Table 27-5
BLB11
–
–
–
–
Brown-out Detector trigger level
Brown-out Detector trigger level
Brown-out Detector trigger level
External Reset Disable
Description
1
0
0
1
Protection Type
No restrictions for SPM or LPM accessing the Boot Loader
section.
SPM is not allowed to write to the Boot Loader section.
SPM is not allowed to write to the Boot Loader section, and LPM
executing from the Application section is not allowed to read
from the Boot Loader section. If Interrupt Vectors are placed in
the Application section, interrupts are disabled while executing
from the Boot Loader section.
LPM executing from the Application section is not allowed to
read from the Boot Loader section. If Interrupt Vectors are
placed in the Application section, interrupts are disabled while
executing from the Boot Loader section.
describe briefly the functionality of all the fuses and how
for BODLEVEL Fuse decoding.
(1)(2)
(Continued)
See ”Alternate Functions of Port G” on page
Default Value
1
1
1
1
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
284