ATmega6450P Atmel Corporation, ATmega6450P Datasheet - Page 332

• Manufacturer Part Number: ATmega6450P
• Manufacturer: Atmel Corporation

Specifications of ATmega6450P

• Flash (kbytes): 64 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 25
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

29. Typical Characteristics
29.1
29.1.1
8285D–AVR–06/11
ATmega165A
Active Supply Current
ATmega165A/PA/325A/PA/3250A/PA/645A/P/6450A/P
The following charts show typical behavior. These figures are not tested during manufacturing.
All current consumption measurements are performed with all I/O pins configured as inputs and
with internal pull-ups enabled. A sine wave generator with rail-to-rail output is used as clock
source.
All Active- and Idle current consumption measurements are done with all bits in the PRR register
set and thus, the corresponding I/O modules are turned off. Also the Analog Comparator is dis-
abled during these measurements.
the additional current consumption compared to I
trolled by the Power Reduction Register. See
The power consumption in Power-down mode is independent of clock selection.
The current consumption is a function of several factors such as: operating voltage, operating
frequency, loading of I/O pins, switching rate of I/O pins, code executed and ambient tempera-
ture. The dominating factors are operating voltage and frequency.
The current drawn from capacitive loaded pins may be estimated (for one pin) as C
C
The parts are characterized at frequencies higher than test limits. Parts are not guaranteed to
function properly at frequencies higher than the ordering code indicates.
The difference between current consumption in Power-down mode with Watchdog Timer
enabled and Power-down mode with Watchdog Timer disabled represents the differential cur-
rent drawn by the Watchdog Timer.
Figure 29-1. ATmega165A: Active Supply Current vs. Frequency (0.1 - 1.0MHz)
L
= load capacitance, V
0.25
0.15
0.05
0.2
0.1
0
0
0.1
CC
0.2
= operating voltage and f = average switching frequency of I/O pin.
0.3
Table 29-1 on page 337
0.4
Frequency (MHz)
”Power Reduction Register” on page 41
0.5
CC
Active and I
0.6
0.7
and
CC
Table 29-2 on page 337
Idle for every I/O module con-
0.8
0.9
1
L
*
5.5 V
5.0 V
4.5 V
4.0 V
3.3 V
2.7 V
1.8 V
V
for details.
CC
*f where
show
332