SAM7X128 Atmel Corporation, SAM7X128 Datasheet - Page 516
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
SAM7X128
Manufacturer Part Number
SAM7X128
Description
Manufacturer
Atmel Corporation
Specifications of SAM7X128
Flash (kbytes)
128 Kbytes
Pin Count
100
Max. Operating Frequency
55 MHz
Cpu
ARM7TDMI
Hardware Qtouch Acquisition
No
Max I/o Pins
62
Ext Interrupts
62
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
2
Twi (i2c)
1
Uart
3
Can
1
Ssc
1
Ethernet
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
384
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
32
Self Program Memory
NO
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
3.3
Operating Voltage (vcc)
3.0 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- Current page: 516 of 687
- Download datasheet (11Mb)
36.6.5
36.6.5.1
516
SAM7X512/256/128
Low-power Mode
Enabling Low-power Mode
Reactive overload frames are automatically handled by the CAN controller even if the OVL bit in
the CAN_MR register is not set. An overload flag is generated in the same way as an error flag,
but error counters do not increment.
In Low-power Mode, the CAN controller cannot send or receive messages. All mailboxes are
inactive.
In Low-power Mode, the SLEEP signal in the CAN_SR register is set; otherwise, the WAKEUP
signal in the CAN_SR register is set. These two fields are exclusive except after a CAN control-
ler reset (WAKEUP and SLEEP are stuck at 0 after a reset). After power-up reset, the Low-
power Mode is disabled and the WAKEUP bit is set in the CAN_SR register only after detection
of 11 consecutive recessive bits on the bus.
A software application can enable Low-power Mode by setting the LPM bit in the CAN_MR
global register. The CAN controller enters Low-power Mode once all pending transmit messages
are sent.
When the CAN controller enters Low-power Mode, the SLEEP signal in the CAN_SR register is
set. Depending on the corresponding mask in the CAN_IMR register, an interrupt is generated
while SLEEP is set.
The SLEEP signal in the CAN_SR register is automatically cleared once WAKEUP is set. The
WAKEUP signal is automatically cleared once SLEEP is set.
Reception is disabled while the SLEEP signal is set to one in the CAN_SR register. It is impor-
tant to note that those messages with higher priority than the last message transmitted can be
received between the LPM command and entry in Low-power Mode.
Once in Low-power Mode, the CAN controller clock can be switched off by programming the
chip’s Power Management Controller (PMC). The CAN controller drains only the static current.
Error counters are disabled while the SLEEP signal is set to one.
Thus, to enter Low-power Mode, the software application must:
Now the CAN Controller clock can be disabled. This is done by programming the Power Man-
agement Controller (PMC).
– Set LPM field in the CAN_MR register
– Wait for SLEEP signal rising
6120I–ATARM–06-Apr-11
Related parts for SAM7X128
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![U641B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
![U4082B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
![U4255BM-M](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B-P](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
![TDA4470](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
![ATF22V10B-25PC](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
![AT89C51ED2-IM](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
![AT24C01](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
![U6046B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: