SAM7X256 Atmel Corporation, SAM7X256 Datasheet - Page 532

• Manufacturer Part Number: SAM7X256
• Manufacturer: Atmel Corporation

Specifications of SAM7X256

• Flash (kbytes): 256 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 55 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 62
• Ext Interrupts: 62
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 3
• Can: 1
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

36.8.1
Name:
Access Type:
• CANEN: CAN Controller Enable
0 = The CAN Controller is disabled.
1 = The CAN Controller is enabled.
• LPM: Disable/Enable Low Power Mode
w Power Mode.
1 = Enable Low Power M
CAN controller enters Low Power Mode once all pending messages have been transmitted.
• ABM: Disable/Enable Autobaud/Listen mode
0 = Disable Autobaud/listen mode.
1 = Enable Autobaud/listen mode.
• OVL: Disable/Enable Overload Frame
0 = No overload frame is generated.
1 = An overload frame is generated after each successful reception for mailboxes configured in Receive with/without over-
write Mode, Producer and Consumer.
• TEOF: Timestamp messages at each end of Frame
0 = The value of CAN_TIM is captured in the CAN_TIMESTP register at each Start Of Frame.
1 = The value of CAN_TIM is captured in the CAN_TIMESTP register at each End Of Frame.
• TTM: Disable/Enable Time Triggered Mode
0 = Time Triggered Mode is disabled.
1 = Time Triggered Mode is enabled.
• TIMFRZ: Enable Timer Freeze
0 = The internal timer continues to be incremented after it reached 0xFFFF.
1 = The internal timer stops incrementing after reaching 0xFFFF. It is restarted after a timer reset. See
nal Timer Counter” on page
532
DRPT
31
23
15
–
–
–
7
SAM7X512/256/128
CAN Mode Register
TIMFRZ
30
22
14
CAN_MR
Read-write
–
–
–
6
529.
TTM
29
21
13
–
–
–
5
TEOF
28
20
12
–
–
–
4
OVL
27
19
11
–
–
–
3
ABM
26
18
10
–
–
2
RXSYNC
LPM
25
17
–
9
–
1
“Freezing the Inter-
6120I–ATARM–06-Apr-11
CANEN
24
16
–
8
–
0