SAM7X256 Atmel Corporation, SAM7X256 Datasheet - Page 543

• Manufacturer Part Number: SAM7X256
• Manufacturer: Atmel Corporation

Specifications of SAM7X256

• Flash (kbytes): 256 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 55 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 62
• Ext Interrupts: 62
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 1
• Uart: 3
• Can: 1
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

36.8.6
Name:
Access Type:
Any modification on one of the fields of the CANBR register must be done while CAN module is disabled.
To compute the different Bit Timings, please refer to the
• PHASE2: Phase 2 segment
This phase is used to compensate the edge phase error.
Warning: PHASE2 value must be different from 0.
• PHASE1: Phase 1 segment
This phase is used to compensate for edge phase error.
• PROPAG: Programming time segment
This part of the bit time is used to compensate for the physical delay times within the network.
• SJW: Re-synchronization jump width
To compensate for phase shifts between clock oscillators of different controllers on bus. The controller must re-synchronize
on any relevant signal edge of the current transmission. The synchronization jump width defines the maximum of clock
cycles a bit period may be shortened or lengthened by re-synchronization.
• BRP: Baudrate Prescaler.
This field allows user to program the period of the CAN system clock to determine the individual bit timing.
The BRP field must be within the range [1, 0x7F], i.e., BRP = 0 is not authorized.
• SMP: Sampling Mode
0 = The incoming bit stream is sampled once at sample point.
1 = The incoming bit stream is sampled three times with a period of a MCK clock period, centered on sample point.
SMP Sampling Mode is automatically disabled if BRP = 0.
6120I–ATARM–06-Apr-11
31
23
15
–
–
–
7
–
CAN Baudrate Register
t
t
t
t
t
PHS2
PHS1
PRS
SJW
CSC
=
=
=
=
=
30
22
14
CAN_BR
Read-write
–
–
6
t
t
(
CSC
CSC
t
t
BRP
CSC
CSC
×
×
×
×
+
(
(
1
(
(
PROPAG
SJW
PHASE2
PHASE1
)
⁄
PHASE1
MCK
+
29
21
13
–
5
1
)
+
+
+
1
1
1
SJW
)
)
)
28
20
12
–
4
Section 36.6.4.1 “CAN Bit Timing Configuration” on page
BRP
27
19
11
–
–
3
–
26
18
10
–
2
SAM7X512/256/128
PROPAG
PHASE2
25
17
–
9
1
SMP
24
16
8
0
510.
543