SPC5561MZQ132 Freescale Semiconductor / Motorola, SPC5561MZQ132 Datasheet - Page 49

• Manufacturer Part Number: SPC5561MZQ132
• Description: Power Architecture TM 32-bit MCU for Automotive
• Manufacturer: Freescale Semiconductor / Motorola

Freescale Semiconductor
Table 2
Table 4
Table 5
Table 6
Location
Absolute Maximum Ratings:
EMI Testing Specifications:
ESD Characteristics: Added (Electromagnetic Static Discharge) in the table title.
VCR/POR Electrical Specifications:
• Deleted Spec 3, “Flash core voltage.”
• Spec 12 “DC Input Voltage”: Deleted from second line‘. . .except for eTPUB15 and SINB (DSPI_B_SIN)’ leaving
• Spec 12 “DC Input Voltage”: Added footnote 8 to second line “V
• Spec 14, column 2, changed: ‘V
• Spec 15, column 2, changed: ‘V
• Spec 21, Added the name of the spec, ‘V
• Spec 28 “Maximum Solder Temperature”: Added two sublines:
• Footnote 1, added: ‘any of’ between ‘beyond’ and ‘the listed maxima.’
• Deleted footnote 2: ‘Absolute maximum voltages are currently maximum burn-in voltages. Absolute maximum
• Footnote 6 (now footnote 5): Added the following sentence to the end, “Keep the negative DC voltage greater
• Changed the maximum operating frequency to from 132 to f
• Footnote 2: Deleted ‘Refer to Table 1 for the maximum operating frequency.’
• Subscript all symbol names that appear after the first underscore character.
• Specs 7 and 10: added ‘at Tj ‘at the end of the first line in the second column: Characteristic.
• Footnote 10: Deleted ‘Preliminary value. Final specification pending characterization.”
• Added to Spec 2:
• Spec 3: Added new footnote 3 for both lines: ‘It is possible to reach the current limit during ramp up--do not treat
• Spec 5: Changed old Footnote 1 (now footnote 2): ‘User must be able to supply full operating current for the 1.5V
• Spec 10:
• Added new footnote 1 to Spec 3: “ V
• Rewrote old footnote 7(new footnote 9) to: Represents the worst-case external transistor BETA. It is measured
• Deleted old footnote 8: ‘Preliminary value. Final specification pending characterization.’
V
min. and max values of -0.3 and 6.5 respectively, and deleted old footnote 7.
structures hold the input voltage less than the maximum voltage on all pads powered by the V
maximum injection current specification is met (s mA for all pins) and V
specifications.
reference to
Lead free (PbFree) and Leaded (SnPb) with maximum values of 260 C and 245 C respectively.
specifications for device stress have not yet been determined.’Spec 26 “Maximum Operating Temperature
Range”: replaced -40 C with T
than -0.6 V on SINB during the internal power-on reset (POR) state.”
this event as a short circuit current.’
supply when the 3.3V supply reaches this range.” to ‘Supply full operating current for the 1.5 V supply when the
3.3 V supply reaches this range.”
on a per part basis and calculated as (I
3.3 V (V
3.3 V (V
• Changed the minimum values of: -40 C = 60; 25 C = 65; 150 C = 85.
• Added old footnote 5 as new footnote 6.
• Removed ‘Tj ‘after ‘150 C’ in the last line, second column: Characteristic.
• Added a new footnote 7, ‘Refer to
• Rewrote old footnote 7(new footnote 9) to: Represents the worst-case external transistor BETA. It is measured
• Added cross-reference to footnote 6: ‘I
DDEH
on a per part basis and calculated as (I
V
RC33
Table 28. Table and Figure Changes Between Rev. 0.0 and 1.0 (continued)
powered I/O pads. Deleted third line ‘V
DDSYN
DDSYN
= 3.1 V, V
Table
) POR negated (ramp down)
) POR asserted (ramp up)
9, DC Electrical Specifications, to which the Spec was moved.
VRCCTL
MPC5561 Microcontroller Data Sheet, Rev. 2.0
= 2.2 V.’ Changed ‘(@ V
L
.
SS
DD
differential voltage’ to ‘V
differential voltage’ to ‘V
IL_S
Table 1
DD
(Table
VRCCTL
RC33
Description of Changes
DD
÷
for the maximum operating frequency.’
÷
I
DDEH
Min. 0.0
VRCCTL
to V
Min. 0.0
9, Spec 15) is guaranteed to scale with V
I
VRCCTL
is measured at the following conditions: V
DDSYN
DD
powered by I/O pads (eTPUB15 and SINB), including the
).
= 1.35 V, f
).
differential voltage,’ as well as the name and cross
Max. 0.30
SS
DD
Max. 0.30
MAX
to V
to V
Revision History for the MPC5561 Data Sheet
DDE
.
sys
SSA
DDA
= f
powered I/O pads” that reads: ‘Internal
MAX
differential voltage.’
V
differential voltage.’
DDE
V
)‘ to ‘(@ f
is within the operating voltage
sys
= f
DDEH6
MAX
DD
DDE
).’
= 1.35 V,
down to V
supplies, if the
POR5
49
.