SPC5561MZQ132 Freescale Semiconductor / Motorola, SPC5561MZQ132 Datasheet - Page 53

• Manufacturer Part Number: SPC5561MZQ132
• Description: Power Architecture TM 32-bit MCU for Automotive
• Manufacturer: Freescale Semiconductor / Motorola

5.2
The following table lists the changes made throughout the document.
Freescale Semiconductor
Table 22
Table 23
Table 24
Table 24
Figure 16
Table 25
Table 26
Figure 27
Section 1,
deserialization and serialization, and chaining. Removed reference to SIU_DISR register.
Table 6
Location
Location
VCR/POR Electrical Specifications:
Bus Operation Timing:
External Interrupt Timing:
eTPU Timing,
eMIOS Timing:
DSPI Timing:
EQADC SSI Timing Characteristics:
eMIOS Timing Added figure.
MPC5561 324 Package:
“Overview”: Added new 11th paragraph about FlexRay. Removed discussion in the SIU and DSPI paragraphs about
Information Changed Between Revisions 1.0 and 2.0
Added to Specs 1, 2 and 3 that reads: On power up, assert RESET before V
(internal POR). RESET must remain asserted until the power supplies are within the operating conditions as
specified in
outside the operating conditions and until the internal POR asserts.
• Changed Spec 1 for the minimum 67 MHz column from: 15.2 to 14.9.
• Specs 5 and 6: corrected format to show the bus timing values for various frequencies with EBTS bit = 0 and
• Footnote 1: Deleted ‘f
• Deleted second figure after table ‘External Interrupt Setup Timing.’
• Deleted (MTS) from the heading, table, and footnotes.
• Footnote 1: Deleted ‘. . .f
• Added Footnote 2: ‘This specification does not include the rise and fall times. When calculating the minimum
• Added to beginning of footnote 1 ‘All DSPI timing specifications use the fastest slew rate (SRC = 0b11) on pad
• Footnote 1: Deleted ‘V
• Deleted from table title ‘(Pads at 3.3 V or 5.0 V)’
• Deleted 1st line in table ‘CLOAD = 25 pF on all outputs. Pad drive strength set to maximum.’
• Spec 1: FCK frequency -- removed.
• Combined footnotes 1 and 2, and moved the new footnote to Spec 2. Moved old footnote 3 to Spec 2.
• Footnote 1, deleted ‘V
• Footnote 2: added ‘cycle’ after ‘duty’ to read: FCK duty cycle is not 50% when . . . .
• Changed ball label T21 from VRCVSS to PLLCFG2.
• Deleted the version number and date.
EBTS bit = 1.
with SRC = 0b11.’
eMIOS pulse width, include the rise and fall times defined in the slew rate control fields (SRC) of the pad
configuration registers (PCR).’
type M or MH. DSPI signals using pad types of S or SH have an additional delay based on the slew rate.’
Changed ‘CL = 50 pF’ to ‘CL = 25 pF.’
Table 28. Table and Figure Changes Between Rev. 0.0 and 1.0 (continued)
Figure 16
Table 9
Table 29. Information Changed Between Rev. 1.0 and Rev. 2.0
DC Electrical Specifications. On power down, assert RESET before any power supplies fall
eTPU Timing and
SYS
DD
DD
MPC5561 Microcontroller Data Sheet, Rev. 2.0
SYS
= 1.35–1.65 V’ and ‘V
= 132 MHz’, ‘.V
= 1.35–1.65 V’ and ‘V
= 132 MHz. . .’, ‘. . .V
Figure 17
DD33
Description of Changes
Description of Changes
and V
DD33
eTPU Input/Output Timing: Deleted – No eTPU in MPC5561.
DD33
DD33
DDSYN
and V
and V
and V
DDSYN
= 3.0–3.6 V’ and ‘ and CL = 200 pF with SRC = 0b11.’
DDSYN
DDSYN
Revision History for the MPC5561 Data Sheet
= 3.0–3.6V.’
= 3.0–3.6 V.
= 3.0–3.6 V. . .’ and ‘ . . .and CL = 200 pF
POR15
, V
POR33
, and V
POR5
negate
53