pnx1500 NXP Semiconductors, pnx1500 Datasheet - Page 89
pnx1500
Manufacturer Part Number
pnx1500
Description
Pnx15xx Series Connected Media Processor
Manufacturer
NXP Semiconductors
Datasheet
1.PNX1500.pdf
(828 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
pnx1500E
Manufacturer:
NORTEL
Quantity:
1 000
- Current page: 89 of 828
- Download datasheet (8Mb)
Philips Semiconductors
Volume 1 of 1
PNX15XX_SER_3
Product data sheet
3.5 Semaphores
3.6 I
After wake-up from sleep mode, the TM3260 CPU can examine the tentative wake-up
attempt, and if the wake-up is genuine, bring the system back to full operational
mode.
In addition, the clocks to individual unused modules can be turned off altogether and
the idle() task of the operating system can be used to activate a voluntary powerdown
mechanism in the CPU. These modes are not managed by a hardware power mode
controller, but by software using the standard provisions of the CPU and the clock
system.
The semaphore module implements 16 semaphores for mutual-exclusion in a multi-
processor environment. Each processor in the system (at board level) can request a
particular semaphore. All 16 semaphores are accessed through the same bus which
guarantees atomic accesses.
There is no built-in mapping of semaphores to sharable hardware system resources.
Such mapping is done by software convention.
Each semaphore behaves as follows:
Only the lower 12 bits of the semaphore are writable. These lower 12 bits are used by
software to write a unique ID decided by software convention. The upper 20 bits
always return 0 when read.
The I
The I
100 kHz, and the fast mode, which runs at 400 kHz.
The I
peripherals like video/audio ADC/DACs at board level.
2
C Interface
–
–
–
if (current_content == 0)
else if (write_value == 0) new_content = 0;
2
2
2
C interface on the PNX15xx Series provides I
C interface supports two operating modes, the standard mode, which runs at
C interface may be used to connect an optional boot EEPROM and/or other
an external wake-up event on pin GPIO[15]. When entering in sleep mode, the
GPIO[15] pin state (i.e. value of the pin) is sampled and registered. The CPU
is woken up if the pin GPIO[15] changes state (from low to high) after the
system has gone into sleep mode. The GPIO[15] pin is observable by
software.
an expired internal counter. Before entering in sleep mode, this special
counter is set up to count XTAL_IN clock ticks. Once the count is satisfied, the
CPU is woken up. The counter has 32 bits.
an incoming event is detected by the GPIO module (could be a Remote
Control ‘power on’ command). Before going into sleep mode, the CPU sets the
GPIO event queues to monitor a selected group of GPIO pins. Once the
queues are full or have monitored an event, the CPU is woken up (via an
interrupt). This is a more sophisticated wake-up event than the wake-up upon
transition on GPIO[15] pin event, since several events are sampled and
therefore keep the GPIO alive.
Rev. 3 — 17 March 2006
new_content = write_value;
2
C master and slave capability.
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
PNX15xx Series
Chapter 2: Overview
2-8
Related parts for pnx1500
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
Standard level N-channel enhancement mode Field-Effect Transistor (FET) in a plastic package using NXP High-Performance Automotive (HPA) TrenchMOS technology
Manufacturer:
NXP Semiconductors
Datasheet: