MC68HC711PH8 Motorola, MC68HC711PH8 Datasheet - Page 179
MC68HC711PH8
Manufacturer Part Number
MC68HC711PH8
Description
High-density Complementary Metal Oxide Semiconductor (HCMOS) Microcomputer Unit
Manufacturer
Motorola
Datasheet
1.MC68HC711PH8.pdf
(264 pages)
- Current page: 179 of 264
- Download datasheet (2Mb)
9.1.7
The A/D conversion sequence begins one E clock cycle after a write to the A/D control/status
register, ADCTL. The bits in ADCTL select the channel and the mode of conversion.
An input voltage equal to V
(full scale), with no overflow indication. For ratiometric conversions of this type, the source of each
analog input should use V
9.2
ADPU (bit 7 of the OPTION register) controls A/D converter power up. Clearing ADPU removes
power from and disables the A/D converter system; setting ADPU enables the A/D converter
system. After the A/D converter is turned on, the analog bias voltages will take up to 100 s to
stabilize.
When the A/D converter system is operating from the MCU E clock, all switching and comparator
operations are synchronized to the MCU clocks. This allows the comparator results to be sampled
at ‘quiet’ times, which minimizes noise errors. The internal RC oscillator is asynchronous with
respect to the MCU clock, so noise can affect the A/D converter results. This results in a slightly
lower typical accuracy when using the internal oscillator (CSEL = 1).
9.2.1
The 8-bit special-purpose OPTION register sets internal system configuration options during
initialization. The time protected control bits, IRQE, DLY, FCME and CR[1:0] can be written to only
once in the first 64 cycles after a reset and then they become read-only bits. This minimizes the
possibility of any accidental changes to the system configuration. They may be written at any time
in special modes.
ADPU — A/D power-up
After enabling the A/D power, at least 100 s should be allowed for system stabilization.
MC68HC11PH8
System conÞg. options 1 (OPTION)
1 (set)
0 (clear) –
Conversion process
A/D converter power-up and clock select
OPTION — System configuration options register 1
–
A/D system power enabled.
A/D system disabled, to reduce supply current.
RH
RL
Address
as the supply voltage and be referenced to V
ANALOG-TO-DIGITAL CONVERTER
$0039
converts to $00 and an input voltage equal to V
ADPU CSEL
bit 7
bit 6
IRQE
bit 5
bit 4
DLY
CME
bit 3
FCME
bit 2
RL
CR1
bit 1
.
RH
converts to $FF
CR0
bit 0
MOTOROLA
0001 0000
on reset
State
TPG
9-5
9
Related parts for MC68HC711PH8
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Motorola, Inc [VOLTAGE REGULATOR]
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
3N2046367254 MOTOROLA SC (XSTRS/R F)
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
MOTOROLA POWERPC 603e MICROPROCESSOR
Manufacturer:
Motorola
Part Number:
Description:
Motorola Semiconductor Datasheet Library
Manufacturer:
Motorola
Part Number:
Description:
SWITCHMODE Schottky Power Rectifier(POWERTAP III Package)
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
SWITCHMODE Schottky Power Rectifirer
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Hybrid Power Module
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Hybrid Power Module
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Search -----> MTE53N50E
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Hybrid Power Module
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
Hybrid Power Module
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
SCHOTTKY BARRIER RECTIFIER 200 AMPERES 60 VOLT
Manufacturer:
Motorola
Datasheet:
Part Number:
Description:
NPN SILICON POWER DARLINGTON TRANSISTOR
Manufacturer:
Motorola
Datasheet: