CY8C36_10 CYPRESS [Cypress Semiconductor], CY8C36_10 Datasheet - Page 33

• Manufacturer Part Number: CY8C36_10
• Manufacturer: CYPRESS [Cypress Semiconductor]

global busses or to one of the analog mux buses to connect any
pin to any internal analog resource such as ADC or comparators.
In addition, select pins provide direct connections to specific
analog features such as the high current DACs or uncommitted
opamps.
6.4.9 CapSense
This section applies only to GPIO pins. All GPIO pins may be
used to create CapSense buttons and sliders
“CapSense”
6.4.10 LCD Segment Drive
This section applies only to GPIO pins. All GPIO pins may be
used to generate Segment and Common drive signals for direct
glass drive of LCD glass. See the
page 52 for details.
6.4.11 Adjustable Output Level
This section applies only to SIO pins. SIO port pins support the
ability to provide a regulated high output level for interface to
external signals that are lower in voltage than the SIO’s
respective Vddio. SIO pins are individually configurable to output
either the standard Vddio level or the regulated output, which is
based on an internally generated reference. Typically a voltage
DAC (VDAC) is used to generate the reference (see
6-12). The
use and reference routing to the SIO pins. Resistive pull-up and
pull-down drive modes are not available with SIO in regulated
output mode.
6.4.12 Adjustable Input Level
This section applies only to SIO pins. SIO pins by default support
the standard CMOS and LVTTL input levels but also support a
differential mode with programmable levels. SIO pins are
grouped into pairs. Each pair shares a reference generator block
which, is used to set the digital input buffer reference level for
interface to external signals that differ in voltage from Vddio. The
reference sets the pins voltage threshold for a high logic level
(see
Typically a voltage DAC (VDAC) generates the V
“DAC”
reference routing to the SIO pins.
Document Number: 001-53413 Rev. *I
Note
19. GPIOs with opamp outputs are not recommended for use with CapSense
0.5 × Vddio
0.4 × Vddio
0.5 × V
V
REF
Figure
section on page 53 has more details on VDAC use and
REF
“DAC”
6-12). Available input thresholds are:
section on page 53 for more information.
section on page 53 has more details on VDAC
“LCD Direct Drive”
PRELIMINARY
[19]
. See the
REF
section on
Figure
reference.
Figure 6-12. SIO Reference for Input and Output
6.4.13 SIO as Comparator
This section applies only to SIO pins. The adjustable input level
feature of the SIOs as explained in the
section can be used to construct a comparator. The threshold for
the comparator is provided by the SIO's reference generator. The
reference generator has the option to set the analog signal
routed through the analog global line as threshold for the
comparator. Note that a pair of SIO pins share the same
threshold.
The digital input path in
functionality. In the figure, ‘Reference level’ is the analog signal
routed through the analog global. The hysteresis feature can
also be enabled for the input buffer of the SIO, which increases
noise immunity for the comparator.
6.4.14 Hot Swap
This section applies only to SIO pins. SIO pins support ‘hot swap’
capability to plug into an application without loading the signals
that are connected to the SIO pins even when no power is
applied to the PSoC device. This allows the unpowered PSoC to
maintain a high impedance load to the external device while also
preventing the PSoC from being powered through a GPIO pin’s
protection diode.
PSoC
Input Path
Output Path
Output
Digital
Digital
Input
SIO_Ref
®
3: CY8C36 Family Datasheet
Drive
Logic
Figure 6-9
Reference
Generator
Driver
Vhigh
Voutref
Vinref
on page 30 illustrates this
Adjustable Input Level
Page 33 of 112
PIN
[+] Feedback