ISP1362EE/01 PHILIPS [NXP Semiconductors], ISP1362EE/01 Datasheet - Page 10
ISP1362EE/01
Manufacturer Part Number
ISP1362EE/01
Description
Single-chip Universal Serial Bus On-The-Go controller
Manufacturer
PHILIPS [NXP Semiconductors]
Datasheet
1.ISP1362EE01.pdf
(150 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISP1362EE/01
Manufacturer:
KAWASAKI
Quantity:
1 200
Part Number:
ISP1362EE/01
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
- Current page: 10 of 150
- Download datasheet (620Kb)
Philips Semiconductors
Table 2:
9397 750 12337
Product data
Symbol
V
DGND
DACK1
DACK2
INT1
INT2
RESET
H_SUSPEND/
H_WAKEUP
D_SUSPEND/
D_WAKEUP
H_PSW1
CC
[1]
Pin description
26
27
28
29
30
31
32
33
34
35
LQFP64
Pin
…continued
J7
K7
J8
K8
J9
K9
K10
J10
H9
H10
TFBGA64
Ball
Type
-
-
I
I
O
O
I
I/O
I/O
O
[2]
Rev. 03 — 06 January 2004
Description
supply voltage (3.3 V); it is recommended to connect a decoupling
capacitor of 0.01 F
digital ground
DMA acknowledge input; indicates that a request for DMA transfer
from the HC has been granted by the DMA controller; the active level
(HIGH or LOW) of the acknowledge signal is programmed by using the
HcHardwareConfiguration register (20H/A0H); when not in use, this
pin must be connected to V
input with hysteresis
DMA acknowledge input; indicates that a request for DMA transfer
from the DC has been granted by the DMA controller; the active level
(HIGH or LOW) of the acknowledge signal is programmed by using the
DcHardwareConfiguration register (BAH/BBH); when not in use, this
pin must be connected to V
input with hysteresis
interrupt request from the HC; provides a mechanism for the HC to
interrupt the microprocessor; see HcHardwareConfiguration register
(20H/A0H)
If the OneINT bit of the HcHardwareConfiguration register is set to
logic 1, both the HC and DC interrupt request will be routed to INT1.
push-pull output
interrupt request from the DC; provides a mechanism for the DC to
interrupt the microprocessor; see DcHardwareConfiguration register
(BAH/BBH)
push-pull output
reset input
input with hysteresis and internal pull-up resistor
I/O pin (open-drain); goes HIGH when the HC is in the ‘suspend’
mode; a LOW pulse must be applied to this pin to wake up the HC;
connect a 100 k resistor to V
bidirectional, push-pull input, three-state open-drain output
I/O pin (open-drain); goes HIGH when the DC is in the ‘suspend’
mode; a LOW pulse must be applied to this pin to wake up the DC;
connect a 100 k resistor to V
bidirectional, push-pull input, three-state open-drain output
connects to the external PMOS switch; required when the external
charge pump or external V
downstream port
LOW — switches ON the PMOS providing V
port
HIGH — switches OFF the PMOS
when not in use, leave this pin open
open-drain output
Section 15.4.1
Section 16.1.4
for details
BUS
for details
CC
CC
through a 10 k resistor
through a 10 k resistor
CC
CC
is used for providing V
Single-chip USB OTG controller
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
BUS
to the downstream
ISP1362
BUS
to the
10 of 150
Related parts for ISP1362EE/01
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
General purpose CMOS timer
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Voltage regulator diodes
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5V, 3.3 V and 2.5V dual UART, 5 Mbit/s (max.),with 32-byte FIFOs and infrared(IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.), with 64-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Master I-2C - bus controller with UART interface
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
BTL stereo Class-D audio amplifier with I2S input
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
3.4 W PDM input class-D audio amplifier
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
TRIODE FOR USE AS GROUNDED GRID U.H.F. AMPLIFIER
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Specific Thales (NXP : BLA0912-250,112)
Manufacturer:
Philips Semiconductors
Part Number:
Description:
Specific Thales (NXP : MX0912B251Y,114)
Manufacturer:
Philips Semiconductors