ISP1362EE/01 PHILIPS [NXP Semiconductors], ISP1362EE/01 Datasheet - Page 115
ISP1362EE/01
Manufacturer Part Number
ISP1362EE/01
Description
Single-chip Universal Serial Bus On-The-Go controller
Manufacturer
PHILIPS [NXP Semiconductors]
Datasheet
1.ISP1362EE01.pdf
(150 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISP1362EE/01
Manufacturer:
KAWASAKI
Quantity:
1 200
Part Number:
ISP1362EE/01
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
- Current page: 115 of 150
- Download datasheet (620Kb)
Philips Semiconductors
Table 114: DcHardwareConfiguration register: bit allocation
9397 750 12337
Product data
Bit
Symbol
Reset
Access
Bit
Symbol
Reset
Access
reserved
DAKOLY
R/W
15
7
0
-
-
16.1.4 DcHardwareConfiguration register (R/W: BBH/BAH)
DRQPOL
Table 113: DcMode register: bit description
This command is used to access the DcHardwareConfiguration register, which
consists of two bytes. The first (lower) byte contains the device configuration and
control values, the second (upper) byte holds the clock control bits and the clock
division factor. The bit allocation is given in
of the programmed bit values.
The DcHardwareConfiguration register controls the connection to the USB bus, clock
activity and power supply during the ‘suspend’ state, as well as output clock
frequency, DMA operating mode and pin configurations (polarity, signalling mode).
Code (Hex): BA/BB — write or read DcHardwareConfiguration register
Transaction — write or read 2 bytes (code or data)
EXTPUL
Bit
7 to 6
5
4
3
2
1
0
R/W
R/W
14
0
6
1
Symbol
-
GOSUSP
-
INTENA
DBGMOD
-
SOFTCT
NOLAZY
DAKPOL
R/W
R/W
13
1
5
0
Rev. 03 — 06 January 2004
CLKRUN
reserved
Description
reserved
Writing logic 1 followed by logic 0 will activate the ‘suspend’
mode.
reserved
Logic 1 enables all interrupts. Bus reset value: unchanged.
Logic 1 enables debug mode, in which all NAKs and errors will
generate an interrupt. Logic 0 selects normal operation, in which
interrupts are generated on every ACK (bulk endpoints) or after
every data transfer (isochronous endpoints). Bus reset value:
unchanged.
reserved
Logic 1 enables SoftConnect. This bit is ignored if EXTPUL = 1
in the DcHardwareConfiguration register (see
reset value: unchanged.
Remark: In the OTG mode, this bit is ignored. The LOC_CONN
bit of the OtgControl register controls the pull-up resistor on the
OTG_DP1 pin.
R/W
12
0
4
0
-
WKUPCS
R/W
R/W
11
0
3
0
Table
114. A bus reset will not change any
reserved
Single-chip USB OTG controller
R/W
R/W
10
0
2
1
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
CKDIV[3:0]
INTLVL
R/W
R/W
9
1
1
0
ISP1362
Table
114). Bus
INTPOL
115 of 150
R/W
R/W
8
1
0
0
Related parts for ISP1362EE/01
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
General purpose CMOS timer
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.) with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Voltage regulator diodes
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5V, 3.3 V and 2.5V dual UART, 5 Mbit/s (max.),with 32-byte FIFOs and infrared(IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
5 V, 3.3 V and 2.5 V quad UART, 5 Mbit/s (max.), with 64-byte FIFOs and infrared (IrDA) encoder/decoder
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Single UART with I2C-bus/SPI interface, 64 bytes of transmit and receive FIFOs, IrDA SIR built-in support
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Master I-2C - bus controller with UART interface
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
BTL stereo Class-D audio amplifier with I2S input
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
3.4 W PDM input class-D audio amplifier
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
TRIODE FOR USE AS GROUNDED GRID U.H.F. AMPLIFIER
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
Specific Thales (NXP : BLA0912-250,112)
Manufacturer:
Philips Semiconductors
Part Number:
Description:
Specific Thales (NXP : MX0912B251Y,114)
Manufacturer:
Philips Semiconductors