E28F016XS20 INTEL [Intel Corporation], E28F016XS20 Datasheet - Page 8

• Manufacturer Part Number: E28F016XS20
• Description: 16-MBIT (1 MBIT x 16, 2 MBIT x 8) SYNCHRONOUS FLASH MEMORY
• Manufacturer: INTEL [Intel Corporation]

28F016XS FLASH MEMORY
address inputs. During read operations, addresses
are latched and accesses are initiated on a rising
CLK edge in conjunction with ADV# low. Both CLK
and ADV# are ignored by the 28F016XS during
command/data write sequences.
The
technology, providing V
and 5.0V and program and erase capability at
V
28F016XS consumes less than one half the power
consumption at 5.0V V
highest read performance capability. V
at 5.0V eliminates the need for a separate 12.0V
converter, while the V
program/erase performance. In addition to the
flexible program and erase voltages, the dedicated
V
V
A 3/5# input pin configures the device’s internal
circuitry for optimal 3.3V or 5.0V read/program
operation.
A Command User Interface (CUI) serves as the
system interface between the microprocessor or
microcontroller and the internal memory operation.
Internal Algorithm Automation allows program and
block erase operations to be executed using a Two-
Write command sequence to the CUI in the same
way as the 28F008SA 8-Mbit FlashFile™ memory.
Software locking of memory blocks is an added
feature of the 28F016XS as compared to the
28F008SA. The 28F016XS provides selectable
block locking to protect code or data such as direct-
executable operating systems or application code.
Each block has an associated nonvolatile lock-bit
which determines the lock status of the block. In
addition, the 28F016XS has a master Write Protect
pin (WP#) which prevents any modifications to
memory blocks whose lock-bits are set.
Writing of memory data is performed in either byte
or word increments, typically within 6 µs at 12.0V
V
28F008SA. A block erase operation erases one of
the 16 blocks in typically 1.2 sec, independent of
the other blocks.
Each block can be written and erased a minimum of
100,000 cycles. Systems can achieve one million
8
PP
PP
PPLK
PP
, which is a 33% improvement over the
= 12.0V or 5.0V. Operating at V
gives complete code protection with V
.
28F016XS
incorporates
PP
CC
CC
= 12.0V option maximizes
, while 5.0V V
operation at both 3.3V
CC
SmartVoltage
PP
CC
= 3.3V, the
operation
provides
PP
Block Erase Cycles by providing wear-leveling
algorithms and graceful block retirement. These
techniques have already been employed in many
flash file systems and hard disk drive designs.
All operations are started by a sequence of Write
commands to the device. Three Status Registers
(described in detail later in this datasheet) and a
RY/BY# output pin provide information on the
progress of the requested operation.
The following Status Registers are used to provide
device and WSM operation information to the user:
The GSR and BSR memory maps for Byte-Wide
and Word-Wide modes are shown in Figures 5
and 6.
The 28F016XS incorporates an open drain RY/BY#
output pin. This feature allows the user to OR-tie
many RY/BY# pins together in a multiple memory
configuration such as a Resident Flash Array.
The 28F016XS also incorporates a dual chip-
enable function with two input pins, CE
These pins have exactly the same functionality as
the regular chip-enable pin, CE#, on the 28F008SA.
For minimum chip designs, CE
ground and system logic may use CE
enable input. The 28F016XS uses the logical
combination of these two signals to enable or
disable the entire chip. Both CE
be active low to enable the device. If either one
becomes inactive, the chip will be disabled. This
feature, along with the open drain RY/BY# pin,
allows the system designer to reduce the number of
control pins used in a large array of 16-Mbit
devices.
A Compatible Status Register (CSR) which is
100% compatible with the 28F008SA FlashFile
memory Status Register. The CSR, when used
alone, provides a straightforward upgrade
capability to the 28F016XS from a 28F008SA-
based design.
A Global Status Register (GSR) which also
informs the system of overall Write State
Machine (WSM) status.
16 Block Status Registers (BSRs) which
provide block-specific status information such
as the block lock-bit status.
1
0
# may be tied to
# and CE
0
0
# as the chip
# and CE
1
# must
1
#.