MT9171AE1 ZARLINK [Zarlink Semiconductor Inc], MT9171AE1 Datasheet
MT9171AE1
Related parts for MT9171AE1
MT9171AE1 Summary of contents
Page 1
Features • Full duplex transmission over a single twisted pair • Selectable 80 or 160 kbit/s line rate • Adaptive echo cancellation • (9171) and 4 km (9172) • ISDN compatible (2B+D) data format • Transparent ...
Page 2
Both devices function identically but with the DSIC having a shorter maximum loop reach specification. The generic "DNIC" will be used to reference both devices unless otherwise noted. The MT9171/72 is fabricated in ...
Page 3
Pin Description (continued) Pin # Name CDSTi/ Control/Data ST-BUS In/Control/Data In (Digital). A 2.048 Mbit/s serial control CDi & signalling input in DN mode. In MOD mode this is a continuous bit stream at ...
Page 4
DSTi DSTo F0o Channel Time 0 Figure Port - 80 kbit/s (Modes DSTi ...
Page 5
Functional Description The MT9171/ device which may be used in practically any application that requires high speed data transmission over two wires, including smart telephone sets, workstations, data terminals and computers. The device supports the 2B+D channel format ...
Page 6
DSTo ...
Page 7
CDSTo CDSTi F0o 3.9 µsec 62.5 µsec Channel Time 0 CLD TCK ...
Page 8
Receive Interface separates the channels and outputs them to the proper ports in the proper channel times. The destination of the various channels is the same as that received on the input DV and CD ports. The ...
Page 9
Mode - SLAVE The chip timebase is extracted from the received line data and the external 10.24 MHz SLV crystal is phase locked provide clocks for the entire device and are output for the external system to ...
Page 10
In MOD mode, DUAL port operation must be used and the D, B1 and B2 channel designations no longer exist. The selection of SLV or MAS will determine which of the DNICs is using the externally supplied clock and which ...
Page 11
CD Port (CDSTi/CDi, CDSTo/CDo) The CD port is a serial bidirectional port used only in DUAL port mode means by which the DNIC receives its control information for things such as setting the bit rate, enabling internal ...
Page 12
Reg Sel-1 Reg Sel-2 Bit Name 2 6 ATTACK Convergence Speedup. When set to ’1’, the echo canceller will converge to the reflection coefficient much faster. Used on power-up for fast convergence. canceller will require the ...
Page 13
Reg Sel-1 Reg Sel-2 Bit Name 1 4 FUN Force Unsync. When set to ’1’, the DNIC is forced out-of-sync to test the SYNC recovery circuitry. When set to ’0’, the operation continues in synchronization. 1 ...
Page 14
In MOD mode, the CD port is no longer an ST-BUS but is a serial bit stream operating at the bit rate selected. It continues to transfer the C-channel but the D-channel and the HK bit no longer exist. DUAL ...
Page 15
Bits Bit 7 Bit 6 Data 1 1 NRZ Data Differential Encoded Differential Encoded Biphase Transmit Line Signal Note: Last bit sent was a logic SYNC OUT 7 0 Figure 11 - Frame Format ...
Page 16
F0 SYNC HK0 OUT Figure 12 - Frame Format - 160 kbit/s (Modes Applications Typical connection diagrams are shown in Figures 13 and 14 for the DN mode ...
Page 17
MT9171/72 DSTi DV Port ST-BUS { DSTo L OUT CDSTi { CD Port ST-BUS CDSTo F0 { Master Clocks C4 MS0 Mode Select MS1 Lines OSC1 MS2 0.33 µ OSC2 Ref V Bias 0.33 µF Figure 14 ...
Page 18
Absolute Maximum Ratings** - Voltages are with respect to ground (V Parameter 1 Supply Voltage 2 Voltage on any pin (other than supply) 3 Current on any pin (other than supply) 4 Storage Temperature 5 Package Power Dissipation (Derate 16mW/ ...
Page 19
DC Electrical Characteristics - Voltages are with respect to ground (V Characteristics 11 Input High Voltage (ex OSC1) 12 Input Low Voltage (ex OSC1) 13 Input High Voltage (OSC1 Input Low Voltage (OSC1 ...
Page 20
AC Electrical Characteristics - Clock Timing - DN Mode (Figures 16 & 17) Characteristics 1 C4 Clock Period 2 C4 Clock Width High or Low 3 Frame Pulse Setup Time 4 Frame Pulse Hold Time 5 Frame Pulse Width ...
Page 21
AC Electrical Characteristics - Clock Timing - MOD Mode (Figure 18) Characteristics 1 TCK/RCK Clock Period 2 TCK/RCK Clock Width 3 TCK/RCK Clock Transition Time 4 CLD to TCK Setup Time 5 CLD to TCK Hold Time 6 CLD ...
Page 22
AC Electrical Characteristics - Data Timing - DN Mode (Figure 19) Characteristics 1 DSTi/CDSTi Data Setup Time 2 DSTi/CDSTi Data Hold Time 3a DSTo/CDSTo Data Delay 3b DSTo/CDSTo High Z to Data Delay † Timing is over recommended temperature ...
Page 23
Performance Characteristics of the MT9172 DNIC Characteristics 1 Allowable Attenuation for Bit Error -6 Rate of 10 (Note 1) 2 Line Length at 80 kbit/s -24 AWG -26 AWG 3 Line Length at 160 kbit/s -24 AWG -26 AWG Note ...
Page 24
TCK 0.4V 2.0V Di CDI 0. 2.4V CDo 0.4V RCK 2.4V Do 0.4V Figure 21 - Data Timing for Slave Modem Mode MT9171/ ¼ Zarlink Semiconductor Inc. Data Sheet t ...
Page 25
...
Page 26
...
Page 27
...
Page 28
For more information about all Zarlink products Information relating to products and services furnished herein by Zarlink Semiconductor Inc. or its subsidiaries (collectively “Zarlink”) is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in ...