K9K1G08U0M-YIB0 Samsung semiconductor, K9K1G08U0M-YIB0 Datasheet - Page 4

• Manufacturer Part Number: K9K1G08U0M-YIB0
• Description: 128M x 8 Bit NAND Flash Memory
• Manufacturer: Samsung semiconductor

Product Introduction
The K9K1G08U0M is a 1,026Mbit(1,107,296,436 bit) memory organized as 262,144 rows(pages) by 528 columns. Spare sixteen col-
umns are located from column address of 512 to 527. A 528-byte data register is connected to memory cell arrays accommodating
data transfer between the I/O buffers and memory during page read and page program operations. The memory array is made up of
16 cells that are serially connected to form a NAND structure. Each of the 16 cells resides in a different page. A block consists of the
32 pages formed by two NAND structures, totaling 16,384 NAND structures of 16 cells. The array organization is shown in Figure 2.
The program and read operations are executed on a page basis, while the erase operation is executed on a block basis. The memory
array consists of 8,192 separately erasable 16K-byte blocks. It indicates that the bit by bit erase operation is prohibited on the
K9K1G08U0M.
The K9K1G08U0M has addresses multiplexed into 8 I/O's. This scheme dramatically reduces pin counts and allows systems
upgrades to future densities by maintaining consistency in system board design. Command, address and data are all written through
I/O's by bringing WE to low while CE is low. Data is latched on the rising edge of WE. Command Latch Enable(CLE) and Address
Latch Enable(ALE) are used to multiplex command and address respectively, via the I/O pins. The 128M byte physical space
requires 27 addresses, thereby requiring four cycles for byte-level addressing: column address, low row address and high row
address, in that order. Page Read and Page Program need the same four address cycles following the required command input. In
Block Erase operation, however, only the three row address cycles are used. Device operations are selected by writing specific c om-
mands into the command register. Table 1 defines the specific commands of the K9K1G08U0M.
The device provides simultaneous program/erase capability up to four pages/blocks. By dividing the memory array into eight 128Mbit
separate planes, simultaneous multi-plane operation dramatically increases program/erase performance by 4X while still maintaining
the conventional 512 byte structure.
The extended pass/fail status for multi-plane program/erase allows system software to quickly identify the failing page/block ou t of
selected multiple pages/blocks. Usage of multi-plane operations will be described further throughout this document.
In addition to the enhanced architecture and interface, the device incorporates copy-back program feature from one page to another
of the same plane without the need for transporting the data to and from the external buffer memory. Since the time-consuming burst-
reading and data-input cycles are removed, system performance for solid-state disk application is significantly increased.
Table 1. Command Sets
NOTE : 1. The 00h command defines starting address of the 1st half of registers.
K9K1G08U0M-YCB0, K9K1G08U0M-YIB0
Caution : Any undefined command inputs are prohibited except for above command set of Table 1.
Read 1
Read 2
Read ID
Reset
Page Program (True)
Page Program (Dummy)
Copy-Back Program(True)
Copy-Back Program(Dummy)
Block Erase
Multi-Plane Block Erase
Read Status
Read Multi-Plane Status
2. Page Program(True) and Copy-Back Program(True) are available on 1 plane operation.
3. The 71h command should be used for read status of Multi Plane operation.
Page Program(Dummy) and Copy-Back Program(Dummy) are available on the 2nd,3rd,4th plane of multi plane operation.
After data access on the 2nd half of register by the 01h command, the status pointer is
The 01h command defines starting address of the 2nd half of registers.
automatically moved to the 1st half register(00h) on the next cycle.
Function
(2)
(2)
(2)
(2)
1st. Cycle
60h----60h
00h/01h
71h
50h
90h
FFh
80h
80h
00h
03h
60h
70h
(3)
(1)
4
2nd. Cycle
10h
11h
8Ah
8Ah
D0h
D0h
-
-
-
-
-
-
3rd. Cycle
10h
11h
-
-
-
-
-
-
-
-
-
-
FLASH MEMORY
Acceptable Command
during Busy
O
O
O