DS1875T+ Maxim Integrated Products, DS1875T+ Datasheet - Page 16

• Manufacturer Part Number: DS1875T+
• Description: IC SFP CTRLR/TRIPLEXER 38-TQFN
• Manufacturer: Maxim Integrated Products

Specifications of DS1875T+

• Applications: Fiber Optics
• Interface: I²C
• Voltage - Supply: 2.85 V ~ 3.9 V
• Package / Case: *
• Mounting Type: Surface Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PON Triplexer and SFP Controller
The DS1875 integrates the control and monitoring func-
tionality required to implement a PON system using
Maxim’s MAX3643 compact burst-mode laser driver.
The compact laser-driver solution offers a considerable
cost benefit by integrating control and monitoring fea-
tures in the low-power CMOS process, while leaving
only the high-speed portions to the laser driver. Key
components of the DS1875 are shown in the Block
Diagram and described in subsequent sections. Table
1 contains a list of acronyms used in this data sheet.
Table 1. DS1875 Acronyms
16
ACRONYM
10GEPON
SFF-8472
______________________________________________________________________________________
GEPON
BPON
GPON
EPON
ROSA
CATV
TOSA
FTTH
SFP+
FTTX
PWM
ADC
AGC
DAC
RSSI
APC
APD
PON
LOS
LUT
SFF
SFP
BM
TIA
ER
TE
10-Gigabit Ethernet PON
Analog-to-Digital Converter
Automatic Gain Control
Automatic Power Control
Avalanche Photodiode
Burst Mode
Broadband PON
Cable Television
Ethernet PON
Extinction Ratio
Digital-to-Analog Converter
Fiber-to-the-Home
Fiber-to-the-X
Gigabit Ethernet PON
Gigabit PON
Loss of Signal
Lookup Table
Tracking Error
Transimpedance Amplifier
Receiver Optical Subassembly
Receive Signal Strength Indicator
Passive Optical Network
Pulse-Width Modulation
Small Form Factor
Document Defining Register Map of
SFPs and SFFs
Small Form Factor Pluggable
Enhanced SFP
Transmit Optical Subassembly
Detailed Description
DEFINITION
Bias current is controlled by an APC loop. The APC
loop uses digital techniques to overcome the difficulties
associated with controlling burst-mode systems.
This is the default mode of operation. In autodetect bias
control, transmit burst length is monitored. A “short
burst” is declared when the burst is shorter than
expected based on the sample rate setting in Table
02h, Register 88h. In the case that 32 consecutive short
bursts are transmitted, the integrator is disabled and
the BIAS DAC is loaded from the BIAS LUT (Table 08h).
Any single burst of adequate burst length re-enables
the APC integrator.
Open-loop control is configured by setting FBOL in
Table 02h, Register C7h. In this mode, the BIAS LUT
(Table 08h) is directly loaded to the BIAS DAC output.
The BIAS LUT can be programmed in 2°C increments
over the 40°C to +102°C range. It is left-shifted so that
the LUT value is loaded to either the DAC MSB or the
DAC MSB-1 (Bit BOLFS, Table 02h, Register 89h).
The closed-loop control requires a burst length long
enough to satisfy the sample rate settings in Table 02h,
Register 88h (APC_SR[3:0]). Closed-loop control is
configured by setting FBCL in Table 02h, Register C7h.
In this mode, the APC integrator is enabled, which con-
trols the BIAS DAC.
The APC loop begins by loading the value from the
BIAS LUT (Table 08h) indexed by the present tempera-
ture conversion. The feedback for the APC loop is the
monitor diode (BMD) current, which is converted to a
voltage using an external resistor. The feedback volt-
age is compared to an 8-bit scaleable voltage refer-
ence, which determines the APC set point of the
system. Scaling of the reference voltage accommo-
dates the wide range in photodiode sensitivities. This
allows the application to take full advantage of the APC
reference’s resolution.
The DS1875 has an LUT to allow the APC set point to
change as a function of temperature to compensate for
TE. The TE LUT (Table 05h) has 36 entries that deter-
mine the APC setting in 4°C windows between -40°C to
+100°C. Ranging of the APC DAC is possible by pro-
gramming a single byte in Table 02h, Register 8Dh.
Closed-Loop Bias Control
Open-Loop Bias Control
Autodetect Bias Control
Bias Control