M30260F6AGP#U5A Renesas Electronics America, M30260F6AGP#U5A Datasheet - Page 183

• Manufacturer Part Number: M30260F6AGP#U5A
• Description: IC M16C MCU FLASH 48K 48LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/26r

Specifications of M30260F6AGP#U5A

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, PWM, Voltage Detect, WDT
• Number Of I /o: 39
• Program Memory Size: 48KB (48K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 48-LQFP
• Cpu Family: R8C
• Device Core Size: 16b
• Frequency (max): 20MHz
• Interface Type: UART
• Total Internal Ram Size: 2KB
• # I/os (max): 39
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 3V
• On-chip Adc: 12-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -20C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Package: 48LQFP
• Family Name: R8C
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 39
• Number Of Timers: 8
• For Use With: R0K33026AS000BE - KIT DEV EVALUATION M16C/26A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

R
R
M
e
E
1
. v
J
6
Figure 13.1.3.1.1. Detection of Start and Stop Condition
0
C
2
9
0 .
B
2 /
0
0
6
13.1.3.1 Detection of Start and Stop Condition
13.1.3.2 Output of Start and Stop Condition
2
A
0
F
Whether a start or a stop condition has been detected is determined.
A start condition-detected interrupt request is generated when the SDA
to low while the SCL
when the SDA
Because the start and stop condition-detected interrupts share the interrupt control register and vec-
tor, check the BBS bit in the U2SMR register to determine which interrupt source is requesting the
interrupt.
A start condition is generated by setting the STAREQ bit in the U2SMR4 register to “1” (start).
A restart condition is generated by setting the RSTAREQ bit in the U2SMR4 register to “1” (start).
A stop condition is generated by setting the STPREQ bit in the U2SMR4 register to “1” (start).
The output procedure is described below.
(1) Set the STAREQ bit, RSTAREQ bit or STPREQ bit to “1” (start).
(2) Set the STSPSEL bit in the U2SMR4 register to “1” (output).
Make sure that no interrupts or DMA transfers will occur between (1) and (2).
The function of the STSPSEL bit is shown in Table 13.1.3.2.1 and Figure 13.1.3.2.1.
2
e
G
0 -
b
1 .
o r
2
NOTE:
3 to 6 cycles < setup time
3 to 6 cycles < hold time
0
, 5
u
0
p
1. When the PCLK1 bit in the PCLKR register is set to "1", the cycles indicates the f1SIO's
SDA2
SDA2
2
(
0
generation frequency cycles; when PCLK1 bit is set to "0", the cycles indicated the f2SIO's
generation frequency cycles.
M
0
7
1
(Start condition)
(Stop condition)
6
SCL2
C
page 164
2
2 /
pin changes state from low to high while the SCL
6
, A
2
M
pin is in the high state. A stop condition-detected interrupt request is generated
1
f o
6
C
3
(1)
2
2 /
(1)
9
6
, B
M
1
Setup time
6
C
2 /
6
) T
Hold time
2
pin is in the high state.
2
pin changes state from high
13. Serial I/O