ST7FLITEU09M6TR STMicroelectronics, ST7FLITEU09M6TR Datasheet - Page 92

• Manufacturer Part Number: ST7FLITEU09M6TR
• Description: MCU 8BIT SGL VOLT FLASH SO-8
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FLITEU09M6TR

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 5
• Program Memory Size: 2KB (2K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 5.5 V
• Data Converters: A/D 5x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Processor Series: ST7FLITEUx
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: ICC
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 5
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7FLITE-SK/RAIS, ST7FLITU0-D/RAIS, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 5 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Connectivity: -
• Lead Free Status / Rohs Status: No

Instruction set
12.2.1
Note:
92/139
Table 43.
Using a prebyte
The instructions are described with 1 to 4 bytes.
In order to extend the number of available opcodes for an 8-bit CPU (256 opcodes), three
different prebyte opcodes are defined. These prebytes modify the meaning of the instruction
they precede.
The whole instruction becomes:
These prebytes enable instruction in Y as well as indirect addressing modes to be
implemented. They precede the opcode of the instruction in X or the instruction using direct
addressing mode. The prebytes are:
Illegal opcode reset
In order to provide enhanced robustness to the device against unexpected behavior, a
system of illegal opcode detection is implemented. If a code to be executed does not
correspond to any opcode or prebyte value, a reset is generated. This, combined with the
Watchdog, allows the detection and recovery from an unexpected fault or interference.
A valid prebyte associated with a valid opcode forming an unauthorized combination does
not generate a reset.
Condition code flag modification
Conditional bit test and branch
Unconditional jump or call
Interruption management
PC-2 End of previous instruction
PC-1 Prebyte
PC Opcode
PC+1 Additional word (0 to 2) according to the number of bytes required to compute
the effective address
PDY 90 Replace an X based instruction using immediate, direct, indexed, or inherent
addressing mode by a Y one.
PIX 92 Replace an instruction using direct, direct bit or direct relative addressing mode
to an instruction using the corresponding indirect addressing mode.
It also changes an instruction using X indexed addressing mode to an instruction using
indirect X indexed addressing mode.
PIY 91 Replace an instruction using X indirect indexed addressing mode by a Y one.
Arithmetic operations
Conditional branch
Logical operations
Shift and rotates
Bit operation
ST7 instruction set (continued)
BSET
TRAP
BTJT
JRxx
AND
ADC
JRA
SLL
SIM
BRES
BTJF
ADD
SRL
JRT
WFI
RIM
OR
HALT
XOR
SUB
SRA
SCF
JRF
IRET
SBC
RCF
CPL
RLC
JP
CALL
NEG
MUL
RRC
ST7LITEU05 ST7LITEU09
CALLR
SWAP
NOP RET
SLA