ATMEGA169-16AI SL710 Atmel, ATMEGA169-16AI SL710 Datasheet - Page 295

• Manufacturer Part Number: ATMEGA169-16AI SL710
• Description: IC AVR MCU 16K 16MHZ IND 64TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA169-16AI SL710

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• For Use With: ATAVRBFLY - KIT EVALUATION AVR BUTTERFLYATSTK502 - MOD EXPANSION AVR STARTER 500
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: ATMEGA16916ASL710

Programming the Flash
Reading the Flash
2514P–AVR–07/06
Before programming the Flash a Chip Erase must be performed, see “Performing Chip
Erase” on page 294.
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Flash write using programming instruction 2a.
3. Load address High byte using programming instruction 2b.
4. Load address Low byte using programming instruction 2c.
5. Load data using programming instructions 2d, 2e and 2f.
6. Repeat steps 4 and 5 for all instruction words in the page.
7. Write the page using programming instruction 2g.
8. Poll for Flash write complete using programming instruction 2h, or wait for t
9. Repeat steps 3 to 7 until all data have been programmed.
A more efficient data transfer can be achieved using the PROG_PAGELOAD
instruction:
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Flash write using programming instruction 2a.
3. Load the page address using programming instructions 2b and 2c. PCWORD
4. Enter JTAG instruction PROG_PAGELOAD.
5. Load the entire page by shifting in all instruction words in the page byte-by-byte,
6. Enter JTAG instruction PROG_COMMANDS.
7. Write the page using programming instruction 2g.
8. Poll for Flash write complete using programming instruction 2h, or wait for t
9. Repeat steps 3 to 8 until all data have been programmed.
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Flash read using programming instruction 3a.
3. Load address using programming instructions 3b and 3c.
4. Read data using programming instruction 3d.
5. Repeat steps 3 and 4 until all data have been read.
A more efficient data transfer can be achieved using the PROG_PAGEREAD
instruction:
1. Enter JTAG instruction PROG_COMMANDS.
2. Enable Flash read using programming instruction 3a.
3. Load the page address using programming instructions 3b and 3c. PCWORD
4. Enter JTAG instruction PROG_PAGEREAD.
5. Read the entire page (or Flash) by shifting out all instruction words in the page
(refer to Table 128 on page 280).
(refer to Table 121 on page 269) is used to address within one page and must be
written as 0.
starting with the LSB of the first instruction in the page and ending with the MSB
of the last instruction in the page. Use Update-DR to copy the contents of the
Flash Data Byte Register into the Flash page location and to auto-increment the
Program Counter before each new word.
(refer to Table 128 on page 280).
(refer to Table 121 on page 269) is used to address within one page and must be
written as 0.
(or Flash), starting with the LSB of the first instruction in the page (Flash) and
ATmega169/V
WLRH
WLRH
295