XRT75R12DIB-F Exar Corporation, XRT75R12DIB-F Datasheet - Page 81

• Manufacturer Part Number: XRT75R12DIB-F
• Description: Peripheral Drivers & Components (PCIs) 12 Channel 3.3V-5V temp -45 to 85C
• Manufacturer: Exar Corporation

Specifications of XRT75R12DIB-F

• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 3.3 V to 5 V
• Package / Case: TBGA-420
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

REV. 1.0.3
T
B
RANSMIT
IT
N
UMBER
2
1
0
C
TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
ONTROL
TxCLKINV
TxLEV
R
TAOS
N
EGISTER
AME
- C
HANNEL N
T
R/W
R/W
R/W
YPE
Transmit All OneS Pattern - Channel_n:
This READ/WRITE bit-field is used to command the Transmit Section of
Channel_n to generate and transmit an unframed, All Ones pattern via the
DS3, E3 or STS-1 line signal (to the remote terminal equipment).
Whenever the user implements this configuration setting, the Transmit Sec-
tion will ignore the data that it is accepting from the System-side equipment
and output the "All Ones" Pattern.
0 - Configures the Transmit Section to transmit the data that it accepts from
the System-side Interface.
1 - Configures the Transmit Section to generate and transmit the Unframed,
All Ones pattern.
Transmit Clock Invert Select - Channel_n:
This READ/WRITE bit-field is used to select the edge of the TxCLK_n input
that the Transmit Section of Channel_n will use to sample the TxPOS_n and
TxNEG_n input pins, as described below.
0 - Configures the Transmit Section (within the corresponding channel) to
sample the TxPOS_n and TxNEG_n input pins upon the falling edge of
TxCLK_n.
1 - Configures the Transmit Section (within the corresponding channel) to
sample the TxPOS_n and TxNEG_n input pins upon the rising edge of
TxCLK_n.
N
Transmit Line Build-Out Select - Channel_n:
This READ/WRITE bit-field is used to enable or disable the Transmit Line
Build-Out (e.g., pulse-shaping) circuit within the corresponding channel.
The user should set this bit-field to either "0" or to "1" based upon the follow-
ing guidelines.
0 - If the cable length between the Transmit Output (of the corresponding
Channel) and the DSX-3/STSX-1 location is 225 feet or less.
1 - If the cable length between the Transmit Output (of the corresponding
Channel) and the DSX-3/STSX-1 location is more than 225 feet .
The user must follow these guidelines in order to insure that the Transmit
Section (of Channel_n) will always generate a DS3 pulse that complies with
the Isolated Pulse Template requirements per Bellcore GR-499-CORE, or
an STS-1 pulse that complies with the Pulse Template requirements per Tel-
cordia GR-253-CORE.
N
OTE
OTE
A
DDRESS
: This is done on a per-channel basis.
: This bit-field is ignored if the channel has been configured to operate
in the E3 Mode.
L
77
OCATION
= 0
XM
4 (
D
ESCRIPTION
M
= 0-5 & 8-D)
XRT75R12D