EP1S10F484I6 Altera, EP1S10F484I6 Datasheet - Page 759

• Manufacturer Part Number: EP1S10F484I6
• Description: IC STRATIX FPGA 10K LE 484-FBGA
• Manufacturer: Altera
• Series: Stratix®r

Specifications of EP1S10F484I6

• Number Of Logic Elements/cells: 10570
• Number Of Labs/clbs: 1057
• Total Ram Bits: 920448
• Number Of I /o: 335
• Voltage - Supply: 1.425 V ~ 1.575 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 484-FBGA
• Family Name: Stratix
• Number Of Logic Blocks/elements: 10570
• # I/os (max): 335
• Frequency (max): 450.05MHz
• Process Technology: 0.13um (CMOS)
• Operating Supply Voltage (typ): 1.5V
• Logic Cells: 10570
• Ram Bits: 920448
• Operating Supply Voltage (min): 1.425V
• Operating Supply Voltage (max): 1.575V
• Operating Temp Range: -40C to 100C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 484
• Package Type: FC-FBGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Not Compliant

Altera Corporation
July 2005
The Quartus II software verifies successful JTAG configuration upon
completion. The software checks the state of CONF_DONE through the
JTAG port. If CONF_DONE is not in the correct state, the Quartus II
software indicates that configuration has failed. If CONF_DONE is in the
correct state, the software indicates that configuration was successful.
1
Do not attempt JTAG and non-JTAG configuration simultaneously. When
configuring through JTAG, allow any non-JTAG configuration to
complete first.
Figure 11–22
device with a microprocessor.
Figure 11–22. JTAG Configuration of Stratix & Stratix GX Devices with a
Microprocessor
Notes to
(1)
(2)
Configuration with JRunner Software Driver
JRunner is a software driver that allows you to configure Altera FPGAs
through the ByteBlasterMV download cable in JTAG mode. The
programming input file supported is in Raw Binary File (.rbf) format.
JRunner also requires a Chain Description File (.cdf) generated by the
Quartus II software. JRunner is targeted for embedded JTAG
configuration. The source code has been developed for the Windows NT
operating system. You can customize the code to make it run on other
platforms.
Connect the nCONFIG, MSEL2, MSEL1, and MSEL0 pins to support a non-JTAG
configuration scheme. If your design only uses JTAG configuration, connect the
nCONFIG pin to V
Pull DATA0 and DCLK to either high or low.
Microprocessor
Figure
If VCCIO is tied to 3.3 V, both the I/O pins and JTAG TDO port
drive at 3.3-V levels.
ADDR
shows the JTAG configuration of a Stratix or Stratix GX
11–22:
Memory
CC
DATA
and the MSEL2, MSEL1, and MSEL0 pins to ground.
(1)
(2)
(2)
Configuring Stratix & Stratix GX Devices
Stratix GX Device
nCONFIG
DATA0
DCLK
TDI
TCK
TMS
Stratix Device Handbook, Volume 2
Stratix or
CONF_DONE
nSTATUS
MSEL2
MSEL1
MSEL0
TDO
V CC
(1)
(1)
(1)
10 kΩ
V CC
10 kΩ
11–41