cs5535 National Semiconductor Corporation, cs5535 Datasheet - Page 370
cs5535
Manufacturer Part Number
cs5535
Description
Geode Cs5535 Companion Multi-function South Bridge
Manufacturer
National Semiconductor Corporation
Datasheet
1.CS5535.pdf
(555 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
cs5535-KSZ
Manufacturer:
CIRRUSLOGIC
Quantity:
20 000
Part Number:
cs5535-UDC
Manufacturer:
AMD
Quantity:
20 000
Part Number:
cs5535-UDCF
Manufacturer:
AMD
Quantity:
20 000
- Current page: 370 of 555
- Download datasheet (4Mb)
www.national.com
UART/IR Controller Register Descriptions
Bit
7:6
5
4
3
2
1
0
Name
RSVD
TXEMP_EV
DMA_EV
MS_EV
LS_EV/TXHLT_EV
TXLDL_EV
RXHDL_EV
Description
Reserved. Read as 0.
Transmitter Empty Event. This bit is the same as bit 6 of the LSR (Length Status
Register). It is set to 1 when the transmitter is empty. (Default = 1.)
DMA Event. This bit is set to 1 when a DMA terminal count (TC) is activated. It is
cleared upon read.
Modem Status Event.
• In UART mode:
• In any IR mode:
Link Status Event
• In UART, Sharp-IR and SIR:
Link Status Event or Transmitter Halted Event
• In CEIR:
Note:
Transmitter Low-Data-Level Event. (Default = 1.)
• FIFOs disabled:
• FIFOs enabled:
Receiver High-Data-Level Event.
• FIFOs disabled:
• FIFOs enabled:
EIR Extended Mode Bit Descriptions
— This bit is set to 1 when any of the 0 to 3 bits in the MSR is set to 1.
— The function of this bit depends on the setting of IRMSSL of the IRCR2
— This bit is set to 1 when a receiver error or break condition is reported. When
— Set to 1 when the receiver is overrun or the transmitter underrun.
— Set to 1 when the transmitter holding register is empty.
— Set to 1 when the TX_FIFO level is below the threshold level.
— Set to 1 when a character is in the receiver holding register.
— Set to 1 when the RX_FIFO is equal to or above threshold or an RX_FIFO
register (see Section 5.12.8.2 "IR Control Register 2 (IRCR2)" on page 390).
When IRMSSL is 0, the bit functions as a modem status interrupt event;
when IRMSSL is set to 1, the bit is forced to 0.
FIFOs are enabled, the parity error, frame error and break conditions are
reported only when the associated character reaches the bottom of the
RX_FIFO. An overrun error is reported as soon as it occurs.
timeout has occurred.
A high-speed CPU can service the interrupt generated by the last frame
byte reaching the RX_FIFO bottom before that byte is transferred to mem-
ory by the DMA controller. This can happen when the CPU interrupt
latency is shorter than the RX_FIFO timeout. A DMA request is generated
only when the RX_FIFO level reaches the DMA threshold or when a FIFO
timeout occurs, in order to minimize the performance degradation due to
DMA signal handshake sequences. If the DMA controller must be set up
before receiving each frame, the software in the interrupt routine should
make sure that the last byte of the frame received has been transferred to
memory before reinitializing the DMA controller, otherwise that byte could
appear as the first byte of the next frame received.
370
(Continued)
Revision 0.8
Related parts for cs5535
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Freescale Semiconductor Technical Data
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Self-calibrating 12-bit Plus Sign Serial I/o A/d Converters With Mux And Sample/hold
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinum Tm Fractional N Rf / Integer N If Dual Low Power Frequency Synthesizer
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinum? 2.0 Ghz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Pllatinumtm 160 Mhz Frequency Synthesizer For Rf Personal Communications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Dual N-channel Enhancement Mode Field Effect Transistor
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Video Amplifier System (obsolete)
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Synchronous Step-up DC/DC Converter For White Led Applications
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
CLC420 - High Speed, Voltage Feedback op Amp, Package: Lcc, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Monolithic Triple 4.5 CRT Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Differential Video Amplifier
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
ADC10061 - 10-Bit 600 NS A/D Converter With Input Multiplexer And Sample/Hold, Package: Soic Wide, Pin Nb=20
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
DS36277 - Dominant Mode Multipoint Transceiver, Package: Soic Narrow, Pin Nb=8
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Printer Solenoid Driver
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Quad High Speed Trapezoidal Bus Transceiver
Manufacturer:
National Semiconductor Corporation
Datasheet: