28119 Parallax Inc, 28119 Datasheet - Page 44
![KIT UNDERSTANDING SIGNALS](/photos/8/97/89794/mfg_28119_sml.jpg)
28119
Manufacturer Part Number
28119
Description
KIT UNDERSTANDING SIGNALS
Manufacturer
Parallax Inc
Datasheet
1.28119.pdf
(137 pages)
Specifications of 28119
Lead Free Status
Contains lead
Accessory Type
Oscilloscope
Interface Type
USB
For Use With/related Products
BASIC Stamp® 2 and Board of Education
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
281197-2
Manufacturer:
TE
Quantity:
20 000
Company:
Part Number:
281197-2
Manufacturer:
MOLEX
Quantity:
2 500
- Current page: 44 of 137
- Download datasheet (5Mb)
Note the ratio of on-time vs. off-time as the signal progresses from left to right. You can
see that the on-time is progressively increasing while the off-time is progressively
decreasing. If this signal were filtered into a smooth DC signal, we would see an analog
voltage starting close to zero and growing to a voltage close to 5 VDC. So, as the duty
cycle increases, the average DC value increases. This is the fundamental principle upon
which the BASIC Stamp recreates sine waves.
Using the PWM output from the BASIC Stamp, a small RC filter, and a piezo speaker,
you can create a sequence of square waves, sine waves, and sound waves that are
viewable on the OPTAscope.
ACTIVITY #1: SINE WAVE SURFING
The goals of this activity are to:
Parts Required
(1) Piezo speaker
(1) 220 Ω resistor
(1) 1.0 µF capacitor
(6) Jumper wires
Building the Sine Wave Measurement Speaker Circuit
•
•
•
•
√
Create a sine wave.
Capture and view it on the OPTAscope.
Vary the frequency of the sine wave and note the change in pitch and volume.
Experiment with the trigger level.
Build the circuit as defined by the schematic in Figure 3-3. Awiring diagram of
the circuit is shown in Figure 3-4. If using the HomeWork Board, omit the 220 Ω
resistor as one is already built in; replace with a jumper wire to make the
necessary connection.
WARNING: The 1.0 µF capacitor can explode if it is connected improperly!
Always disconnect the power before building or modifying circuits. Carefully check the
polarity of the 1.0 µF capacitor. The positive terminal (longer leg) must be connected to a
power source pin and the negative terminal (shorter leg) must be connected to Vss (ground).
Related parts for 28119
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![30008](/images/manufacturer_photos/0/5/515/parallax_inc_tmb.jpg)
Part Number:
Description:
Microcontroller Modules & Accessories DISCONTINUED BY PARALLAX
Manufacturer:
Parallax Inc
![70009](/photos/26/92/269208/70009-l_tmb.jpg)
Part Number:
Description:
BOOK UNDERSTANDING SIGNALS
Manufacturer:
Parallax Inc
Datasheet:
![27404](/photos/26/91/269197/27404-l_tmb.jpg)
Part Number:
Description:
COMPETITION RING FOR SUMOBOT
Manufacturer:
Parallax Inc
Datasheet:
![70016](/photos/8/99/89966/mfg_70016_tmb.jpg)
Part Number:
Description:
TEXT INFRARED REMOTE FOR BOE-BOT
Manufacturer:
Parallax Inc
Datasheet:
![28135](/images/manufacturer_photos/0/5/515/parallax_inc_tmb.jpg)
Part Number:
Description:
BOARD EXPERIMENT+LCD NX-1000
Manufacturer:
Parallax Inc
Datasheet:
![28023](/photos/9/30/93020/mfg_28023_tmb.jpg)
Part Number:
Description:
CONTROLLER 16SERVO MOTOR CONTROL
Manufacturer:
Parallax Inc
Datasheet:
![30010](/photos/9/30/93025/mfg_30010_tmb.jpg)
Part Number:
Description:
BASIC STAMP LOGIC ANALYZER
Manufacturer:
Parallax Inc
Datasheet:
![SX18AC/SO](/images/manufacturer_photos/0/5/515/parallax_inc_tmb.jpg)
Part Number:
Description:
IC MCU 2K FLASH 50MHZ SO-18
Manufacturer:
Parallax Inc
Datasheet: