PIC12HV615-I/SN Microchip Technology, PIC12HV615-I/SN Datasheet - Page 101

• Manufacturer Part Number: PIC12HV615-I/SN
• Description: IC PIC MCU FLASH 1KX14 8SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 12Fr

Specifications of PIC12HV615-I/SN

• Program Memory Type: FLASH
• Program Memory Size: 1.75KB (1K x 14)
• Package / Case: 8-SOIC (3.9mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 5
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC12H
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 64 B
• Interface Type: RS-232/USB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 5
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162083 - HEADER MPLAB ICD2 PIC16F616 8/14
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

11.4.4
The PWM mode supports an Auto-Shutdown mode that
will disable the PWM outputs when an external
shutdown event occurs. Auto-Shutdown mode places
the PWM output pins into a predetermined state. This
mode is used to help prevent the PWM from damaging
the application.
The auto-shutdown sources are selected using the
ECCPASx bits of the ECCPAS register. A shutdown
event may be generated by:
• A logic ‘0’ on the INT pin
• Comparator
• Setting the ECCPASE bit in firmware
FIGURE 11-10:
 2010 Microchip Technology Inc.
From Comparator
INT
ENHANCED PWM AUTO-
SHUTDOWN MODE
ECCPAS<2:0>
AUTO-SHUTDOWN BLOCK DIAGRAM
111
110
101
100
011
010
001
000
PIC12F609/615/617/12HV609/615
From Data Bus
Write to ECCPASE
PRSEN
R
D
Q
S
A shutdown condition is indicated by the ECCPASE
(Auto-Shutdown Event Status) bit of the ECCPAS
register. If the bit is a ‘0’, the PWM pins are operating
normally. If the bit is a ‘1’, the PWM outputs are in the
shutdown state. Refer to Figure 1.
When a shutdown event occurs, two things happen:
The ECCPASE bit is set to ‘1’. The ECCPASE will
remain set until cleared in firmware or an auto-restart
occurs (see Section 11.4.5 “Auto-Restart Mode”).
The enabled PWM pins are asynchronously placed in
their shutdown states. The state of P1A is determined by
the PSSAC bit. The state of P1B is determined by the
PSSBD bit. The PSSAC and PSSBD bits are located in
the ECCPAS register. Each pin may be placed into one
of three states:
• Drive logic ‘1’
• Drive logic ‘0’
• Tri-state (high-impedance)
ECCPASE
PSSAC<1>
PSSBD<1>
PSSAC<0>
P1A_DRV
PSSBD<0>
P1B_DRV
TRISx
TRISx
1
0
1
0
DS41302D-page 101
P1A
P1B