PIC12HV615-I/SN Microchip Technology, PIC12HV615-I/SN Datasheet - Page 30

• Manufacturer Part Number: PIC12HV615-I/SN
• Description: IC PIC MCU FLASH 1KX14 8SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 12Fr

Specifications of PIC12HV615-I/SN

• Program Memory Type: FLASH
• Program Memory Size: 1.75KB (1K x 14)
• Package / Case: 8-SOIC (3.9mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 5
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC12H
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 64 B
• Interface Type: RS-232/USB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 5
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162083 - HEADER MPLAB ICD2 PIC16F616 8/14
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC12F609/615/617/12HV609/615
3.3
To read a program memory location, the user must
write two bytes of the address to the PMADRL and
PMADRH registers, and then set control bit RD
(PMCON1<0>). Once the read control bit is set, the
program memory Flash controller will use the second
instruction cycle after to read the data. This causes the
second instruction immediately following the “
PMCON1,RD
available in the very next cycle in the PMDATL and
PMDATH registers; it can be read as two bytes in the
following instructions. PMDATL and PMDATH regis-
ters will hold this value until another read or until it is
written to by the user (during a write operation).
EXAMPLE 3-1:
DS41302D-page 30
BANKSEL PM_ADR
MOVLW
MOVWF
MOVLW
MOVWF
BANKSEL PMCON1
BSF
NOP
NOP
BANKSEL PMDATL
MOVF
MOVF
Reading the Flash Program
Memory
” instruction to be ignored. The data is
MS_PROG_PM_ADDR
PMADRH
LS_PROG_PM_ADDR
PMADRL
PMCON1, RD
PMDATL, W
PMDATH, W
FLASH PROGRAM READ
; Change STATUS bits RP1:0 to select bank with PMADRL
;
; MS Byte of Program Address to read
;
; LS Byte of Program Address to read
; Bank to containing PMCON1
; PM Read
; First instruction after BSF PMCON1,RD executes normally
; Any instructions here are ignored as program
; memory is read in second cycle after BSF PMCON1,RD
;
; Bank to containing PMADRL
; W = LS Byte of Program PMDATL
; W = MS Byte of Program PMDATL
BSF
 2010 Microchip Technology Inc.