PIC12HV615-I/SN Microchip Technology, PIC12HV615-I/SN Datasheet - Page 96

• Manufacturer Part Number: PIC12HV615-I/SN
• Description: IC PIC MCU FLASH 1KX14 8SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 12Fr

Specifications of PIC12HV615-I/SN

• Program Memory Type: FLASH
• Program Memory Size: 1.75KB (1K x 14)
• Package / Case: 8-SOIC (3.9mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 5
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC12H
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 64 B
• Interface Type: RS-232/USB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 5
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 4-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162083 - HEADER MPLAB ICD2 PIC16F616 8/14
• Eeprom Size: -
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC12F609/615/617/12HV609/615
11.3.4
In Sleep mode, the TMR2 register will not increment
and the state of the module will not change. If the CCP1
pin is driving a value, it will continue to drive that value.
When the device wakes up, TMR2 will continue from its
previous state.
11.3.5
The PWM frequency is derived from the system clock
frequency. Any changes in the system clock frequency
will result in changes to the PWM frequency. See
Section 4.0 “Oscillator Module” for additional
details.
11.3.6
Any Reset will force all ports to Input mode and the
CCP registers to their Reset states.
DS41302D-page 96
OPERATION IN SLEEP MODE
CHANGES IN SYSTEM CLOCK
FREQUENCY
EFFECTS OF RESET
11.3.7
The following steps should be taken when configuring
the CCP module for PWM operation:
1.
2.
3.
4.
5.
6.
• Clear the TMR2IF interrupt flag bit of the PIR1
• Set the Timer2 prescale value by loading the
• Enable Timer2 by setting the TMR2ON bit of
• Wait until Timer2 overflows (TMR2IF bit of the
• Enable the CCP1 pin output driver by clearing
Disable the PWM pin (CCP1) output drivers by
setting the associated TRIS bit.
Set the PWM period by loading the PR2 register.
Configure the CCP module for the PWM mode
by loading the CCP1CON register with the
appropriate values.
Set the PWM duty cycle by loading the CCPR1L
register and DC1B bits of the CCP1CON register.
Configure and start Timer2:
Enable PWM output after a new PWM cycle has
started:
register.
T2CKPS bits of the T2CON register.
the T2CON register.
PIR1 register is set).
the associated TRIS bit.
SETUP FOR PWM OPERATION
 2010 Microchip Technology Inc.