LPC3230FET296/01,5 NXP Semiconductors, LPC3230FET296/01,5 Datasheet - Page 26

• Manufacturer Part Number: LPC3230FET296/01,5
• Description: IC ARM9 MCU 256K 296-TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC32x0r

Specifications of LPC3230FET296/01,5

• Package / Case: 296-TFBGA
• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 266MHz
• Connectivity: EBI/EMI, I²C, IrDA, Microwire, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: DMA, I²S, LCD, Motor Control PWM, PWM, WDT
• Number Of I /o: 51
• Program Memory Type: ROMless
• Ram Size: 256K x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 3.6 V
• Data Converters: A/D 3x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC32
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 256 KB
• Interface Type: EMC
• Maximum Clock Frequency: 266 MHz
• Number Of Timers: 6
• Operating Supply Voltage: 1.31 V to 1.39 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 3 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4964; 935290764551

NXP Semiconductors
LPC3220_30_40_50_1
Preliminary data sheet
7.5.1.2 Single-Level Cell (SLC) NAND flash controller
7.5.2.1 Features
7.5.2 SD card controller
7.5.3 External memory controller
The SLC NAND flash controller interfaces to single-level NAND flash devices. DMA page
transfers are supported, including a 20 byte DMA read and write FIFO. Hardware support
for ECC (Error Checking and Correction) is included for the main data area. Software can
correct a single bit error.
The SD interface allows access to external SD memory cards. The SD card interface
conforms to the SD Memory Card Specification Version 1.01 .
The LPC3220/30/40/50 includes a memory controller that supports data bus SDRAM,
DDR SDRAM, and static memory devices. The memory controller provides an interface
between the system bus and external (off-chip) memory devices.
The controller supports 16-bit and 32-bit wide SDR SDRAM devices of 64 Mbit, 128 Mbit,
128 Mbit, 256 Mbit, and 512 Mbit sizes, as well as 16-bit wide data bus DDR SDRAM
devices of 64 Mbit, 128 Mbit, 128 Mbit, 256 Mbit, and 512 Mbit sizes. Two dynamic
memory chip selects are supplied, supporting two groups of SDRAM:
The memory controller also supports 8-bit, 16-bit, and 32-bit wide asynchronous static
memory devices, including RAM, ROM, and flash, with or without asynchronous page
mode. Four static memory chip selects are supplied for SRAM devices:
The SDRAM controller uses three data ports to allow simultaneous requests from multiple
on-chip AHB bus masters and has the following features.
•
•
•
•
•
•
•
•
•
•
•
•
1-bit and 4-bit data line interface support.
DMA is supported through the system DMA controller.
Provides all functions specific to the SD memory card. These include the clock
generation unit, power management control, command and data transfer.
DYCS0 in the address range 0x8000 0000 to 0x9FFF FFFF
DYCS1 in the address range 0xA000 0000 to 0xBFFF FFFF
CS0 in the address range 0xE000 0000 to 0xE0FF FFFF
CS1 in the address range 0xE100 0000 to 0xE1FF FFFF
CS2 in the address range 0xE200 0000 to 0xE2FF FFFF
CS3 in the address range 0xE300 0000 to 0xE3FF FFFF
Dynamic memory interface supports SDRAM, DDR-SDRAM, and low-power variants.
Read and write buffers to reduce latency and improve performance.
Static memory features include
– asynchronous page mode read
– programmable wait states
– bus turnaround cycles
– output enable and write enable delays
Rev. 01 — 6 February 2009
LPC3220/30/40/50
16/32-bit ARM microcontrollers
© NXP B.V. 2009. All rights reserved.
26 of 73