MC9S08LC36LH Freescale Semiconductor, MC9S08LC36LH Datasheet - Page 185

• Manufacturer Part Number: MC9S08LC36LH
• Description: IC MCU 36K FLASH 2K RAM 64-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08LC36LH

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LCD, LVD, POR, PWM, WDT
• Number Of I /o: 18
• Program Memory Size: 36KB (36K x 8)
• Program Memory Type: FLASH
• Ram Size: 2.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 2x12b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 64-LQFP
• Processor Series: S08LC
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2.5 KB
• Interface Type: I2C/SCI/SPI1/SPI2
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 18
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2-ch x 12-bit
• For Use With: DEMO9S08LC60 - BOARD DEMO FOR 9S08LC60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

10.5.9
The reference clock and the DCO clock are monitored under different conditions (see
Provided the reference frequency is being monitored, ERCS = 1 indicates that the reference clock meets
minimum frequency requirements. When the reference and/or DCO clock(s) are being monitored, if either
one falls below a certain frequency, f
the error. LOCS will remain set until it is acknowledged or until the MCU is reset. LOCS is cleared by
reading ICGS1 then writing 1 to ICGIF (LOCRE = 0), or by a loss-of-clock induced reset (LOCRE = 1),
or by any MCU reset.
If the ICG is in FEE, a loss of reference clock causes the ICG to enter SCM, and a loss of DCO clock causes
the ICG to enter FBE mode. If the ICG is in FBE mode, a loss of reference clock will cause the ICG to
enter SCM. In each case, the CLKST and CLKS bits will be automatically changed to reflect the new state.
If the ICG is in FEE mode when a loss of clock occurs and the ERCS is still set to 1, then the CLKST bits
are set to 10 and the ICG reverts to FBE mode.
A loss of clock will also cause a loss of lock when in FEE or FEI modes. Because the method of clearing
the LOCS and LOLS bits is the same, this would only be an issue in the unlikely case that LOLRE = 1 and
LOCRE = 0. In this case, the interrupt would be overridden by the reset for the loss of lock.
Freescale Semiconductor
1
2
(CLKST = 00)
(CLKST = 01)
(CLKST = 10)
(CLKST = 11)
If ENABLE is high (waiting for external crystal start-up after exiting stop).
DCO clock will not be monitored until DCOS = 1 upon entering SCM from off or FLL bypassed external mode.
Mode
FLL Loss-of-Clock Detection
SCM
FBE
FEE
FEI
Off
0X or 11
CLKS
0X
0X
10
10
10
10
11
11
10
10
11
MC9S08LC60 Series Data Sheet: Technical Data, Rev. 4
Table 10-8. Clock Monitoring (When LOCD = 0)
REFST
X
X
X
X
X
X
0
1
0
1
0
1
LOR
and f
Forced High
Forced High
Forced Low
Forced Low
Real-Time
Forced Low
Forced Low
LOD
Real-Time
Real-Time
Real-Time
Real-Time
Real-Time
ERCS
, respectively, the LOCS status bit will be set to indicate
1
External Reference
Monitored?
Clock
Yes
Chapter 10 Internal Clock Generator (S08ICGV4)
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
(1)
Monitored?
DCO Clock
Table
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
(2)
(2)
(2)
2
10-8).
185