ATTINY26L-8SU Atmel, ATTINY26L-8SU Datasheet - Page 26

• Manufacturer Part Number: ATTINY26L-8SU
• Description: ID MCU AVR 2K 5V 8MHZ 20-SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY26L-8SU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Package: 20SOIC
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 8 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 16
• Interface Type: SPI/USI
• On-chip Adc: 11-chx10-bit
• Number Of Timers: 2
• Cpu Family: ATtiny
• Device Core Size: 8b
• Frequency (max): 8MHz
• Total Internal Ram Size: 128Byte
• # I/os (max): 16
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 20
• Package Type: SOIC
• Processor Series: ATTINY2x
• Core: AVR8
• Data Ram Size: 128 B
• Maximum Clock Frequency: 8 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK505 - ADAPTER KIT FOR 14PIN AVR MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ATTINY26L-8SJ; ATTINY26L-8SJ

Default Clock
Source
Crystal Oscillator
26
ATtiny26(L)
quency of the Watchdog Oscillator is voltage dependent as shown in the Electrical
Characteristics section.
Table 5. Number of Watchdog Oscillator Cycles
The deviced is shipped with CKSEL = “0001”, SUT = “10”, and PLLCK unprogrammed. The
default clock source setting is therefore the internal RC Oscillator with longest startup time. This
default setting ensures that all users can make their desired clock source setting using an In-
System or Parallel Programmer.
XTAL1 and XTAL2 are input and output, respectively, of an inverting amplifier which can be con-
figured for use as an On-chip Oscillator, as shown in Figure 22. Either a quartz crystal or a
ceramic resonator may be used. The maximum frequency for resonators is 12 MHz. The
CKOPT Fuse should always be unprogrammed when using this clock option. C1 and C2 should
always be equal. The optimal value of the capacitors depends on the crystal or resonator in use,
the amount of stray capacitance, and the electromagnetic noise of the environment. Some initial
guidelines for choosing capacitors for use with crystals are given in Table 6. For ceramic resona-
tors, the capacitor values given by the manufacturer should be used.
Figure 22. Crystal Oscillator Connections
The Oscillator can operate in three different modes, each optimized for a specific frequency
range. The operating mode is selected by the fuses CKSEL3..1 as shown in Table 6.
Table 6. Crystal Oscillator Operating Modes
Note:
CKSEL3..1
Typ Time-out (V
101
110
111
(1)
1. This option should not be used with crystals, only with ceramic resonators.
4.1 ms
65 ms
CC
Range (MHz)
Frequency
= 5.0V)
0.4 - 0.9
0.9 - 3.0
3.0 - 16
16 -
Typ Time-out (V
C2
C1
Recommended Range for Capacitors C1 and
4.3 ms
69 ms
C2 for Use with Crystals (pF)
CC
= 3.0V)
XTAL2
XTAL1
GND
12 - 22
12 - 22
12 - 15
–
Number of Cycles
64K (65,536)
4K (4,096)
1477K–AVR–08/10