ATTINY26L-8SU Atmel, ATTINY26L-8SU Datasheet - Page 30

• Manufacturer Part Number: ATTINY26L-8SU
• Description: ID MCU AVR 2K 5V 8MHZ 20-SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY26L-8SU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 2KB (1K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 128 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-SOIC (7.5mm Width)
• Package: 20SOIC
• Device Core: AVR
• Family Name: ATtiny
• Maximum Speed: 8 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 16
• Interface Type: SPI/USI
• On-chip Adc: 11-chx10-bit
• Number Of Timers: 2
• Cpu Family: ATtiny
• Device Core Size: 8b
• Frequency (max): 8MHz
• Total Internal Ram Size: 128Byte
• # I/os (max): 16
• Number Of Timers - General Purpose: 2
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 20
• Package Type: SOIC
• Processor Series: ATTINY2x
• Core: AVR8
• Data Ram Size: 128 B
• Maximum Clock Frequency: 8 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600-DIP40 - STK600 SOCKET/ADAPTER 40-PDIP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK505 - ADAPTER KIT FOR 14PIN AVR MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ATTINY26L-8SJ; ATTINY26L-8SJ

External Clock
30
ATtiny26(L)
EEPROM and Flash access. If EEPROM or Flash is written, do not calibrate to more than 10%
above the nominal frequency. Otherwise, the EEPROM or Flash write may fail. Note that the
oscillator is intended for calibration to 1.0, 2.0, 4.0, or 8.0 MHz. Tuning to other values is not
guaranteed, as indicated in Table 13.
Table 13. Internal RC Oscillator Frequency Range.
To drive the device from an external clock source, XTAL1 should be driven as shown in Figure
24. To run the device on an external clock, the CKSEL Fuses must be programmed to “0000”
and PLLCK to “1”. By programming the CKOPT Fuse, the user can enable an internal 36 pF
capacitor between XTAL1 and GND.
Figure 24. External Clock Drive Configuration
When this clock source is selected, start-up times are determined by the SUT Fuses as shown in
Table 14.
Table 14. Start-up Times for the External Clock Selection
When applying an external clock, it is required to avoid sudden changes in the applied clock fre-
quency to ensure stable operation of the MCU. A variation in frequency of more than 2% from
one clock cycle to the next can lead to unpredictable behaviour. It is required to ensure that the
MCU is kept in reset during such changes in the clock frequency.
OSCCAL Value
SUT1..0
00
01
10
11
$00
$7F
$FF
Start-up Time from
Power-down
Min Frequency in Percentage of
6 CK
6 CK
6 CK
Nominal Frequency
EXTERNAL
SIGNAL
CLOCK
100%
50%
75%
Additional Delay from
Reset (V
Reserved
4.1 ms
65 ms
CC
–
= 5.0V)
PB5 (XTAL2)
XTAL1
GND
Max Frequency in Percentage of
Nominal Frequency
Recommended Usage
BOD enabled
Fast rising power
Slowly rising power
100%
150%
200%
1477K–AVR–08/10