AT90USB162-16MU Atmel, AT90USB162-16MU Datasheet - Page 248

• Manufacturer Part Number: AT90USB162-16MU
• Description: MCU AVR USB 16K FLASH 32-QFN
• Manufacturer: Atmel
• Series: AVR® 90USBr

Specifications of AT90USB162-16MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, PS/2, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-TQFN
• Controller Family/series: AVR USB
• No. Of I/o's: 22
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 16MHz
• Rohs Compliant: Yes
• Processor Series: AT90USBx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI, USART, debugWIRE
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATSTK525, ATSTK526, ATAVRISP2, ATAVRONEKIT, AT90USBKEY, ATEVK525
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK526 - KIT STARTER FOR AT90USB82/162ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK525 - KIT STARTER FOR AT90USBAT90USBKEY2 - KIT DEMO FOR AT90USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details

Serial
Downloading
Serial
Programming Pin
Mapping
248
Table 44. Parallel Programming Characteristics, V
Notes:
Both the Flash and EEPROM memory arrays can be programmed using a serial programming
bus while RESET is pulled to GND. The serial programming interface consists of pins SCK, PDI
(input) and PDO (output). After RESET is set low, the Programming Enable instruction needs to
be executed first before program/erase operations can be executed. NOTE, in Table 45 on page
248, the pin mapping for serial programming is listed. Not all packages use the SPI pins dedi-
cated for the internal Serial Peripheral Interface - SPI.
Table 45. Pin Mapping Serial Programming
Figure 104. Serial Programming and Verify
Notes:
Symbol
t
t
t
BVDV
OLDV
OHDZ
Symbol
PDO
SCK
PDI
1.
2. t
1. If the device is clocked by the internal Oscillator, it is no need to connect a clock source to the
2. V
commands.
XTAL1 pin.
t
WLRH_CE
CC
WLRH
Parameter
BS1 Valid to DATA valid
OE Low to DATA Valid
OE High to DATA Tri-stated
- 0.3V < AVCC < V
is valid for the Write Flash, Write EEPROM, Write Fuse bits and Write Lock bits
is valid for the Chip Erase command.
Pins
PB2
PB3
PB1
PDO
SCK
PDI
CC
+ 0.3V, however, AVCC should always be within 1.8 - 5.5V
XTAL1
RESET
GND
I/O
O
I
I
(1)
CC
AVCC
= 5V ± 10% (Continued)
VCC
Serial Data out
Serial Data in
Description
Serial Clock
+1.8 - 5.5V
+1.8 - 5.5V
Min
0
(2)
Typ
Max
250
250
250
Units
ns
ns
ns
7707A–AVR–01/07